DG429DN-E3
| Parameters | |
|---|---|
| Weight | 722.005655mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Resistance | 150Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 800mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG429 |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 100μA |
| Power Dissipation | 800mW |
| Max Supply Current | 100μA |
| Propagation Delay | 280 ns |
| Turn On Delay Time | 300 ns |
| Logic Function | Multiplexer |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 7V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 20pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Height | 3.69mm |
| Length | 9.04mm |
| Width | 9.04mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-LCC (J-Lead) |
| Number of Pins | 20 |
DG429DN-E3 Overview
Packed in 20-LCC (J-Lead), the electronic component is convenient for shipping overseas. The advanced packaging method Tube provides high reliability. Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have a ratio of 4:1. Operation at a temperature around -40°C~85°C TA. 20 terminations have been made so far. A 4 channel electronic part produces high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. An electrical component like this is included in the 20 series. These analog multiplexers are built based on SP4T switching circuits. A total of 2 circuits make up this switch device. Try searching with DG429 to find analog multiplexer variants. An switch multiplexer with 150Ohm internal resistance has a value of 150Ohm. Datasheets for 20 pin functions are available upon request. Users should never supply a voltage higher than 36V to a switch device. Analogue multiplexers of the Dual, Single supply type that are cost-effective. 13V should be the lowest voltage fed to the electronic component. The switch device would be able to operate with 20μA current. If you put voltage higher than 100μA on the digital multiplexer, damage may occur. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. The voltage should be at least 7V if you are using dual power supplies. Operating voltages range from 15V. A 8 input needs to be operated.
DG429DN-E3 Features
4 Channels
Switch Circuit: SP4T
20μA Supply Current
DG429DN-E3 Applications
There are a lot of Vishay Siliconix DG429DN-E3 Analog Switches & Multiplexers ICs applications.
- Optical Applications
- Data Acquisition Systems
- Battery Powered Instruments
- High reliability control systems
- Power routing
- Wireless Local Loop
- High-Voltage
- Audio/video switches
- Battery Powered Systems
- DSUs
