Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
18-SOIC (0.295, 7.50mm Width) |
Number of Pins |
18 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2009 |
JESD-609 Code |
e3 |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
18 |
Resistance |
150Ohm |
Terminal Finish |
Matte Tin (Sn) |
Max Power Dissipation |
470mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Number of Functions |
1 |
Supply Voltage |
15V |
Base Part Number |
DG429 |
Pin Count |
18 |
Number of Channels |
4 |
Number of Circuits |
2 |
Max Supply Voltage |
36V |
Min Supply Voltage |
13V |
Operating Supply Current |
20μA |
Nominal Supply Current |
100μA |
Power Dissipation |
470mW |
Max Supply Current |
100μA |
Propagation Delay |
250 ns |
Turn On Delay Time |
300 ns |
Logic Function |
Multiplexer |
Number of Inputs |
8 |
Voltage - Supply, Single/Dual (±) |
12V ±15V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
300 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
100Ohm |
Min Dual Supply Voltage |
7V |
Multiplexer/Demultiplexer Circuit |
4:1 |
Off-state Isolation-Nom |
75 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
11pF 20pF |
On-state Resistance Match-Nom |
5Ohm |
Switch Circuit |
SP4T |
Switch Time (Ton, Toff) (Max) |
150ns, 150ns |
Charge Injection |
1pC |
Channel-to-Channel Matching (ΔRon) |
5 Ω |
Switching |
BREAK-BEFORE-MAKE |
Signal Current-Max |
0.03A |
Height |
2.6mm |
Length |
12.45mm |
Width |
8mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
DG429DW-E3 Overview
The electronic component is convenient to ship overseas because it is packed in a 18-SOIC (0.295, 7.50mm Width). High reliability is achieved by using advanced packaging method Tube. Surface Mount is where this multiplexer is located. 4:1 is the number of circuits in the multiplexer and demultiplexer. Temperatures around -40°C~85°C TA are extended for operation. 18 terminations have been made so far. As a result of its 4 channels, this electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 15V voltage supply. An injection of 18 pins is performed into the body of the electrical component. A SP4T switching circuit is used for these analog switches. A total of 2 circuits make up this switch device. Try searching for the analog switch ic with DG429 if you are looking for variants. This digital multiplexer has 150Ohm internal resistance. Please refer to the datasheets for 18 pins functions. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. The lowest voltage the electronic part should receive is 13V. The analogue multiplexer could operate on 20μA current. The analogue multiplexer may be damaged if voltage is greater than 100μA. Despite this switch's dual supply capability, its voltage should not exceed 22V. For dual power supplies, a voltage of at least 7V should be attached. The electrical component supports 8 inputs.
DG429DW-E3 Features
4 Channels
Switch Circuit: SP4T
20μA Supply Current
DG429DW-E3 Applications
There are a lot of Vishay Siliconix DG429DW-E3 Analog Switches & Multiplexers ICs applications.
- Remote wireless modules
- Relay replacements
- Signal routing between systems
- Cable PC
- HDTV
- Residential Gateways, Home Gateway/Router
- ISDN NT1/TA
- Central office
- New designs requiring multiplexer functions
- Cross Connects