DG441AK
| Parameters | |
|---|---|
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 250ns, 120ns |
| Charge Injection | -1pC |
| Channel-to-Channel Matching (ΔRon) | 4Ohm (Max) |
| Crosstalk | -100dB @ 1MHz |
| Drain to Source Resistance | 85Ohm |
| Height | 3.94mm |
| Length | 19.56mm |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
| Mounting Type | Through Hole |
| Package / Case | 16-CDIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Supplier Device Package | 16-CERDIP |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2002 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 85Ohm |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Max Power Dissipation | 900mW |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Max Supply Current | 100μA |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 120 ns |
| Max Dual Supply Voltage | 22V |
DG441AK Overview
The electronic component is convenient to ship overseas because it is packed in a 16-CDIP (0.300, 7.62mm). The advanced packaging method Tube provides high reliability. In Through Hole, you'll find this switch device. 1:1 is the ratio between multiplexers and demultiplexers. Operating temperature extended to -55°C~125°C TA. A SPST - NC switching circuit is used for these analog switches. A 4 circuit is present in this switch device. This digital multiplexer has 85Ohm internal resistance. Datasheets for 16 pin functions are available upon request. Users should never supply a voltage higher than 36V to a switch device. Analog switch ics with Dual, Single supply type are cost-effective. A low voltage of 13V should be applied to the electronic component. The analogue multiplexer may be damaged if voltage is greater than 100μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. In the case of dual power supplies, you should connect at least 7V. Temperatures over 125°C should not be allowed for the multiplexer to operate. It has a Drain to Source resistance of 85Ohm ohms. There is a 16-CERDIP package available from suppliers.
DG441AK Features
Switch Circuit: SPST - NC
Drain-to-Source resistance: 85Ohm
DG441AK Applications
There are a lot of Vishay Siliconix DG441AK Analog Switches & Multiplexers ICs applications.
- SDH
- Digital cross connects (DSX-1)
- Industrial and process control systems
- Modems
- Wireless Local Loop
- Battery Powered Instruments
- High reliability control systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Mechanical reed relay replacement
- Medical Instrumentation
