Parameters |
Factory Lead Time |
1 Week |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Surface Mount |
NO |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2015 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
80Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
470mW |
Technology |
CMOS |
Peak Reflow Temperature (Cel) |
NOT SPECIFIED |
Number of Functions |
4 |
Supply Voltage |
15V |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
NOT SPECIFIED |
Base Part Number |
DG441 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
25V |
Min Supply Voltage |
13V |
Max Supply Current |
1μA |
Turn On Delay Time |
300 ns |
Voltage - Supply, Single/Dual (±) |
12V ±15V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
200 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
80Ohm |
Min Dual Supply Voltage |
7V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
4pF 4pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
220ns, 120ns |
Charge Injection |
-1pC |
Channel-to-Channel Matching (ΔRon) |
2 Ω |
Crosstalk |
-95dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
220ns |
Switch-off Time-Max |
120ns |
Normal Position |
NC |
Height Seated (Max) |
5.08mm |
Length |
20.13mm |
Width |
7.62mm |
RoHS Status |
ROHS3 Compliant |
DG441BDJ Overview
The electronic component is convenient to ship overseas because it is packed in a 16-DIP (0.300, 7.62mm). High reliability is provided by advanced packaging method Tube. This analog switch is mounted in Through Hole. There is 1:1 ratio between the number of multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C TA degrees Celsius. Totally, there are 16 terminations. By its 1 channels, the electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. The electronic part body is injected with 16 pins. Unlike digital switches, these are based on SPST - NC switching circuits. There are 4 circuits in this multiplexer. If you are looking for variants of the digital switch, trying search with DG441. There is 80Ohm internal resistance in this digital multiplexer. For functions related to 16 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 25V. Analog switch ics with Dual, Single supply type are cost-effective. It is recommended that the electrical component receives a voltage of 13V. The analogue multiplexer may be damaged if voltage is greater than 1μA. Despite this switch device's dual supply capability, its voltage should not exceed 22V. The voltage should be at least 7V if you are using dual power supplies. The analog switch ic utilizes SEPARATE OUTPUT outputs in total.
DG441BDJ Features
1 Channels
Switch Circuit: SPST - NC
DG441BDJ Applications
There are a lot of Vishay Siliconix DG441BDJ Analog Switches & Multiplexers ICs applications.
- New designs requiring multiplexer functions
- Remote Powered Equipment
- DSUs
- Multi-Line E1 Interface Cards
- SDH/SONET multiplexers
- Cable Modem
- E1 Multiplexer
- Battery Powered Systems
- Public switching systems
- SONET