Parameters |
Factory Lead Time |
1 Week |
Mount |
Through Hole |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2013 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
90Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
470mW |
Technology |
CMOS |
Peak Reflow Temperature (Cel) |
NOT SPECIFIED |
Number of Functions |
4 |
Supply Voltage |
15V |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
NOT SPECIFIED |
Base Part Number |
DG441 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Number of Channels |
1 |
Max Supply Voltage |
25V |
Min Supply Voltage |
13V |
Operating Supply Current |
5μA |
Power Dissipation |
470mW |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
300 ns |
Number of Inputs |
4 |
Voltage - Supply, Single/Dual (±) |
12V ±15V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
200 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
80Ohm |
Min Dual Supply Voltage |
7V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
4pF 4pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
220ns, 120ns |
Charge Injection |
-1pC |
Channel-to-Channel Matching (ΔRon) |
2 Ω |
Crosstalk |
-95dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
220ns |
Switch-off Time-Max |
120ns |
Normal Position |
NO |
Height Seated (Max) |
5.08mm |
Length |
20.13mm |
Width |
7.62mm |
RoHS Status |
ROHS3 Compliant |
DG441BDJ-E3 Overview
Shipping overseas is convenient due to the electrical component's packing in 16-DIP (0.300, 7.62mm). This packaging method provides high reliability because it uses advanced packaging techniques. This analog switch is mounted in Through Hole. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. A total of 16 terminations have been recorded. A high-quality output is provided by the electrical component's 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. Electronic part bodies are injected with 16 pins. A SPST - NC switching circuit is used for these analog switches. Use DG441 to search for variants of the digital switches. The internal resistance of this digital multiplexer is 90Ohm. Datasheets for functions of 16 pins are available. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users shouldn't supply more than 25V voltage to the switch device. Analogue multiplexers of the Dual, Single supply type that are cost-effective. There should be 13V voltage fed to the electrical part below 13V. This multiplexer would work with 5μA current. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. A dual power supply should have at least 7V voltage attached. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. Operating 4 inputs is required.
DG441BDJ-E3 Features
1 Channels
Switch Circuit: SPST - NC
5μA Supply Current
DG441BDJ-E3 Applications
There are a lot of Vishay Siliconix DG441BDJ-E3 Analog Switches & Multiplexers ICs applications.
- Frame Relay Equipment
- Video switching
- Communication systems
- PBX interfaces
- Remote wireless modules
- Transmit
- SONET
- Cell phones
- Microwave transmission systems
- Switching Systems