DG441BDY
| Parameters | |
|---|---|
| Max Supply Voltage | 25V |
| Min Supply Voltage | 13V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 220 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 120 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 220ns, 120ns |
| Charge Injection | -1pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2015 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 80Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 900mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Number of Circuits | 4 |
DG441BDY Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Extended operating temperature around -40°C~85°C TA. In total, 16 terminations have occurred. The electronic part provides high-quality output because it has 1 channels. A 15V voltage supply should turn on and run the electronic component. An electrical component like this is included in the 16 series. SPST - NC switching circuits are used in these analog switch ics. It consists of 4 circuits. This digital multiplexer has 80Ohm internal resistance. For details about the functions of 16 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 25V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. 13V is the lowest voltage the electrical component should receive. The analogue multiplexer may be damaged if voltage is greater than 1μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. It is recommended that you attach at least 7V to your dual power supply. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
DG441BDY Features
1 Channels
Switch Circuit: SPST - NC
DG441BDY Applications
There are a lot of Vishay Siliconix DG441BDY Analog Switches & Multiplexers ICs applications.
- Microprocessor controlled systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Digital access cross connects
- RGB switches
- Sample hold systems
- Industrial
- E1 Multiplexer
- DSUs
- ISDN NT1/TA
- PBX interfaces
