DG441BDY-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 80Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 900mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG441 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 5μA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 900mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 220 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 120 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 220ns, 120ns |
| Charge Injection | -1pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
DG441BDY-E3 Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). High reliability is ensured by the advanced packaging method Tube. It is mounted in the position Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Increasing operating temperature to around -40°C~85°C TA. 16 terminations have been made so far. A high-quality output is provided by the electrical component's 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. An injection of 16 pins is performed into the body of the electrical component. Unlike digital switches, these are based on SPST - NC switching circuits. Try searching with DG441 if you're looking for variants. Analog switches have 80Ohm internal resistance. For details about the functions of 16 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. Multiplexers should not be powered above 25V in normal situations. Digital switch that provides Dual, Single power at a cost-effective price. A low voltage of 13V should be applied to the electronic component. For this digital switch to work, 5μA current would suffice. Put voltage above 1μA on the multiplexer to cause damage. Despite this switch's dual supply capability, its voltage should not exceed 22V. It is recommended that you attach at least 7V to your dual power supply. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. The 4 inputs need to be operated in order to work.
DG441BDY-E3 Features
1 Channels
Switch Circuit: SPST - NC
5μA Supply Current
DG441BDY-E3 Applications
There are a lot of Vishay Siliconix DG441BDY-E3 Analog Switches & Multiplexers ICs applications.
- T1/E1 Terminals
- PBXs
- Relay replacements
- PCMCIA cards
- Intelligent PBX
- SDH
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Cell phones
- Switching Systems
- Private Branch Exchange (PBX)
