DG441BDY-T1

220ns, 120ns SPST - NC 80Ohm Analog Switches BREAK-BEFORE-MAKE 500pA 16-SOIC (0.154, 3.90mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG441BDY-T1
Package: 16-SOIC (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 426
Description: 220ns, 120ns SPST - NC 80Ohm Analog Switches BREAK-BEFORE-MAKE 500pA 16-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SOIC (0.154, 3.90mm Width)
Number of Pins	16
Weight	665.986997mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2016
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	80Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	900mW
Technology	CMOS
Terminal Form	GULL WING
Number of Functions	4
Terminal Pitch	1.27mm
Reach Compliance Code	unknown
Output	SEPARATE OUTPUT
Qualification Status	Not Qualified
Max Supply Voltage	25V
Min Supply Voltage	13V
Analog IC - Other Type	DPDT
Power Dissipation	900mW
Max Supply Current	1μA
Turn On Delay Time	220 ns
Number of Inputs	4
Voltage - Supply, Single/Dual (±)	12V ±15V
Supply Type	Dual, Single
Turn-Off Delay Time	120 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	80Ohm
Min Dual Supply Voltage	7V
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	4pF 4pF
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	220ns, 120ns
Charge Injection	-1pC
Channel-to-Channel Matching (ΔRon)	2 Ω
Crosstalk	-95dB @ 100kHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	300ns
Normal Position	NC
Height	1.55mm
Length	10mm
Width	4mm
RoHS Status	Non-RoHS Compliant

DG441BDY-T1 Overview

Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. High reliability is achieved by using advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~85°C TA. In total, there are 16 terminations. Circuits based on SPST - NC switching are used to construct these analog switch ics. A 80Ohm internal resistance characterizes this multiplexer. Datasheets for 16 pin functions are available upon request. This switch device is a typical Multiplexer or Switches. Users should never supply a voltage higher than 25V to a switch device. Dual, Single supply type digital switch with a low cost. A low voltage of 13V should be applied to the electronic component. Putting voltage greater than 1μA on the multiplexer may cause damage. There is no problem with using dual supply voltage, but it should not exceed 22V. The voltage should be at least 7V if you are using dual power supplies. There is an analog IC DPDT integrated with this board. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. There are 4 inputs to be operated.