Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
2009 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
85Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
696mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
DG441 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Power Supplies |
+-15V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
20V |
Min Supply Voltage |
4.5V |
Nominal Supply Current |
15μA |
Max Supply Current |
100μA |
Throw Configuration |
SPST |
Turn On Delay Time |
250 ns |
Voltage - Supply, Single/Dual (±) |
10V~30V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
120 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
85Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
60 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
4pF 4pF |
On-state Resistance Match-Nom |
4Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
250ns, 120ns |
Charge Injection |
5pC |
Channel-to-Channel Matching (ΔRon) |
4 Ω (Max) |
Crosstalk |
-100dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NC |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
DG441CY+ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). This high-reliability packaging method uses advanced packaging methods Tube. Multiplexers like this are mounted in the Surface Mount position. 1:1 is the number of circuits in the multiplexer and demultiplexer. Around 0°C~70°C TA is the extended operating temperature. There are 16 terminations totally. A high-quality output is provided by the electrical component's 1 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. This electronic part can be found in the 16 series. These analog multiplexers are built based on SPST - NC switching circuits. Circuits number 4 make up this analogue multiplexer. Try searching for the analog switch ic with DG441 if you are looking for variants. As far as internal resistance is concerned, it has 85Ohm. The datasheets for the 16 pins explain the functions. There is Multiplexer or Switches analog multiplexer like this in the world. A voltage higher than 20V should not normally be supplied to the switches. Digital switch that provides Dual, Single power at a cost-effective price. 4.5V is the lowest voltage the electrical component should receive. A digital multiplexer may suffer damage if voltage is applied above 100μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. If you are using a dual power supply, you should attach at least 4.5V. The analog switch ic utilizes SEPARATE OUTPUT outputs in total.
DG441CY+ Features
1 Channels
Switch Circuit: SPST - NC
DG441CY+ Applications
There are a lot of Maxim Integrated DG441CY+ Analog Switches & Multiplexers ICs applications.
- 65 V DACs
- Access Concentrators
- Digital Cross-Connects
- Mechanical reed relay replacement
- Sample-and-hold systems
- Video switching
- PCMCIA cards
- Residential Gateways, Home Gateway/Router
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Data switching