DG441DJ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 85Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 30mA |
| Power Dissipation | 450mW |
| Max Supply Current | 100μA |
| Turn On Delay Time | 250 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 120 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 220ns, 120ns |
| Charge Injection | -1pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω (Max) |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| RoHS Status | Non-RoHS Compliant |
DG441DJ Overview
As the electronic part is packed in 16-DIP (0.300, 7.62mm), international shipping is convenient. High reliability is achieved by using advanced packaging method Tube. There is an analog multiplexer mounted in position Through Hole. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Extended operating temperature around -40°C~85°C TA. Total terminations are 16. A 15V voltage supply should turn on and run the electronic component. It is part of the design of the 16 series that this electronic component is included. These analog multiplexers are built based on SPST - NC switching circuits. Internally, this switch multiplexer has a resistance of 85Ohm. Please refer to the datasheets for 16 pins functions. A analogue multiplexer of this type is a Multiplexer or Switches. In normalcircumstances, users should not exceed 36V volts for the multiplexer. Analog switch ics with Dual, Single supply type are cost-effective. 13V is the lowest voltage that should be fed to the electronic electronic part. For this multiplexer to operate, 30mA current would be sufficient. A voltage higher than 100μA may cause damage to the switch multiplexer. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. For dual power supplies, a voltage of at least 7V should be attached. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. Operating the 4 inputs requires 4 inputs.
DG441DJ Features
Switch Circuit: SPST - NC
30mA Supply Current
DG441DJ Applications
There are a lot of Vishay Siliconix DG441DJ Analog Switches & Multiplexers ICs applications.
- USB 1.1 signal switching circuits
- SONET/SDH ADM
- Remote wireless modules
- PBX interfaces
- Fiber to the Home
- PDAs
- Frame Relay Equipment
- Voice over IP/DSL – Integrated Access Devices, Smart
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Digital cross connects (DSX-1)
