DG441DJ-E3

220ns, 120ns SPST - NC 85Ohm Analog Switches BREAK-BEFORE-MAKE DG441 16 Pins 500pA 15V 16-DIP (0.300, 7.62mm)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG441DJ-E3
Package: 16-DIP (0.300, 7.62mm)
Datasheet: PDF
Stock: 411
Description: 220ns, 120ns SPST - NC 85Ohm Analog Switches BREAK-BEFORE-MAKE DG441 16 Pins 500pA 15V 16-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Contact Plating	Tin
Mount	Through Hole
Mounting Type	Through Hole
Package / Case	16-DIP (0.300, 7.62mm)
Number of Pins	16
Weight	1.627801g
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2002
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	85Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	450mW
Technology	CMOS
Number of Functions	4
Supply Voltage	15V
Base Part Number	DG441
Pin Count	16
Polarity	Non-Inverting
Number of Channels	1
Max Supply Voltage	36V
Min Supply Voltage	13V
Operating Supply Current	15μA
Nominal Supply Current	15μA
Power Dissipation	450mW
Max Supply Current	100μA
Throw Configuration	SPST
Turn On Delay Time	250 ns
Number of Inputs	4
Voltage - Supply, Single/Dual (±)	12V ±15V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	120 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	85Ohm
Min Dual Supply Voltage	7V
High Level Output Current	30mA
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	60 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	4pF 4pF
On-state Resistance Match-Nom	4Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	220ns, 120ns
Charge Injection	-1pC
Channel-to-Channel Matching (ΔRon)	4 Ω (Max)
Crosstalk	-100dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	85Ohm
Normal Position	NC
Height	3.81mm
Length	21.33mm
Width	7.11mm
Radiation Hardening	No
REACH SVHC	No SVHC
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

DG441DJ-E3 Overview

The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). This packaging method provides high reliability because it uses advanced packaging techniques. In Through Hole, you'll find this switch device. 1:1 is the ratio between multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. In total, there have been 16 terminations. As a result of its 1 channels, this electronic component provides high-quality output. A 15V voltage supply should turn on and run the electronic component. An electrical component of this type can be found in the 16 series. These analog multiplexers are built based on SPST - NC switching circuits. Use DG441 to search for variants of the digital switches. As far as internal resistance is concerned, it has 85Ohm. Datasheets for functions of 16 pins are available. It is a typical Multiplexer or Switches analog multiplexer. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. Dual, Single supply type digital switch with a low cost. There should be 13V voltage fed to the electrical part below 13V. This multiplexer would work with 15μA current. A voltage higher than 100μA may cause damage to the switch multiplexer. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 22V. In the case of dual power supplies, you should connect at least 7V. Among the inputs that can be operated are the 4 inputs. A Drain to Source resistance of 85Ohm is shown for this electronic part.