Parameters |
Factory Lead Time |
1 Week |
Mount |
Through Hole |
Package / Case |
PDIP |
Number of Pins |
16 |
Packaging |
Bulk |
Published |
1999 |
JESD-609 Code |
e3 |
Part Status |
Active |
Number of Terminations |
16 |
Resistance |
160Ohm |
Terminal Finish |
Matte Tin (Sn) - annealed |
Max Operating Temperature |
85°C |
Min Operating Temperature |
-40°C |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Number of Functions |
4 |
Supply Voltage |
15V |
Output |
SEPARATE OUTPUT |
Operating Supply Voltage |
28V |
Temperature Grade |
INDUSTRIAL |
Number of Channels |
1 |
Max Supply Voltage |
40V |
Min Supply Voltage |
5V |
Operating Supply Current |
15μA |
Nominal Supply Current |
15μA |
Max Supply Current |
100μA |
Number of Bits |
4 |
Throw Configuration |
SPST |
Turn On Delay Time |
450 ns |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
200 ns |
Max Dual Supply Voltage |
20V |
Min Dual Supply Voltage |
5V |
Dual Supply Voltage |
18V |
Off-state Isolation-Nom |
60 dB |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
250ns |
Switch-off Time-Max |
120ns |
Drain to Source Resistance |
85Ohm |
Normal Position |
NC |
Height Seated (Max) |
5.33mm |
Length |
19.17mm |
Width |
7.62mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
RoHS Compliant |
Lead Free |
Lead Free |
DG441DJZ Overview
The electronic component is convenient to ship overseas because it is packed in a PDIP. High reliability is achieved by using advanced packaging method Bulk. 16 terminations have been made so far. This electronic part offers high-quality output due to its 1 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. In this multiplexer, the internal resistance is 160Ohm. Datasheets for 16 pin functions are available upon request. Theswitch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 40V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. 5V is the lowest voltage the electrical component should receive. 15μA current would be enough for this multiplexer to operate. Put voltage above 100μA on the multiplexer to cause damage. Despite this switch device's dual supply capability, its voltage should not exceed 20V. In the case of dual power supplies, you should connect at least 5V. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. The electronic component can function from 28V. During operation, the multiplexer should not be exposed to a temperature above 85°C. Drain to Source resistance for this electronic component is 85Ohm. It conducts in a 4-bit manner.
DG441DJZ Features
1 Channels
15μA Supply Current
Drain-to-Source resistance: 85Ohm
4-Bit
DG441DJZ Applications
There are a lot of Intersil (Renesas Electronics America) DG441DJZ Analog Switches & Multiplexers ICs applications.
- Medical Instrumentation
- Sample-and-hold systems
- Industrial
- USB 1.1 signal switching circuits
- Multi-Line E1 Interface Cards
- DSUs
- Public switching systems
- Channelized and Unchannelized DS3 applications
- SONET
- Industrial control systems