DG441DY
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 85Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 900mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 30mA |
| Power Dissipation | 900mW |
| Max Supply Current | 100μA |
| Turn On Delay Time | 250 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 120 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 220ns, 120ns |
| Charge Injection | -1pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω (Max) |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 85Ohm |
| Normal Position | NC |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
DG441DY Overview
The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. This high-reliability packaging method uses advanced packaging methods Tube. Surface Mount is where this multiplexer is located. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. The operating temperature is extended to around -40°C~85°C TA. Totally, there are 16 terminations. When the electronic component is given a voltage of 15V, it should be turned on and run. An electrical component like this is included in the 16 series. Unlike digital switches, these are based on SPST - NC switching circuits. There is 85Ohm internal resistance in this digital multiplexer. To find out what the 16 pins do, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 36V in normal situations. An effective Dual, Single supply digital multiplexer. The lowest voltage the electronic part should receive is 13V. It would be sufficient to run this analogue multiplexer with 30mA current. If put voltage greater than 100μA on the device, damage may be caused to the analogue multiplexer. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. A dual power supply should have at least 7V voltage attached. There are SEPARATE OUTPUT outputs on this analog switch ic. The electrical component supports 4 inputs. Drain to Source resistance for this electronic component is 85Ohm.
DG441DY Features
Switch Circuit: SPST - NC
30mA Supply Current
Drain-to-Source resistance: 85Ohm
DG441DY Applications
There are a lot of Vishay Siliconix DG441DY Analog Switches & Multiplexers ICs applications.
- 65 V DACs
- Residential Gateways, Home Gateway/Router
- Video signal routing
- Cross Connects
- Relay Replacement
- Avionics
- HDTV
- Central office
- Medical systems
- Video switching
