banner_page

DG441DYZ

Analog Switches BREAK-BEFORE-MAKE 15V SOIC


  • Manufacturer: Intersil (Renesas Electronics America)
  • Nocochips NO: 391-DG441DYZ
  • Package: SOIC
  • Datasheet: PDF
  • Stock: 324
  • Description: Analog Switches BREAK-BEFORE-MAKE 15V SOIC(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Surface Mount
Package / Case SOIC
Number of Pins 16
Packaging Bulk
Published 1999
JESD-609 Code e3
Part Status Active
Moisture Sensitivity Level (MSL) 2
Number of Terminations 16
ECCN Code EAR99
Resistance 85Ohm
Terminal Finish Matte Tin (Sn) - annealed
Max Operating Temperature 85°C
Min Operating Temperature -40°C
Subcategory Multiplexer or Switches
Technology CMOS
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 4
Supply Voltage 15V
Terminal Pitch 1.27mm
Time@Peak Reflow Temperature-Max (s) 30
Output SEPARATE OUTPUT
Temperature Grade INDUSTRIAL
Number of Channels 1
Max Supply Voltage 40V
Min Supply Voltage 5V
Power Dissipation-Max 1.6mW
Operating Supply Current 15μA
Number of Bits 4
Throw Configuration SPST
Turn On Delay Time 250 ns
Supply Type Dual, Single
Neg Supply Voltage-Nom (Vsup) -15V
Turn-Off Delay Time 120 ns
Max Dual Supply Voltage 20V
Min Dual Supply Voltage 5V
Dual Supply Voltage 15V
Off-state Isolation-Nom 60 dB
Switching BREAK-BEFORE-MAKE
Drain to Source Resistance 85Ohm
Normal Position NC
Height 1.75mm
Length 10mm
Width 4mm
Radiation Hardening No
REACH SVHC No SVHC
RoHS Status RoHS Compliant
Lead Free Lead Free

DG441DYZ Overview


Due to its SOIC packaging, the electronic part is convenient for international shipping. High reliability is ensured by the advanced packaging method Bulk. A total of 16 terminations have been recorded. Due to its 1 channels, the electrical component produces high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. In this multiplexer, the internal resistance is 85Ohm. To find out what the 16 pins do, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. Users should never supply a voltage higher than 40V to a switch device. Dual, Single supply type digital switch with a low cost. 5V is the lowest voltage the electrical component should receive. For this digital switch to work, 15μA current would suffice. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. In the case of dual power supplies, you should connect at least 5V. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. Temperatures over 85°C should not be allowed for the multiplexer to operate. This electronic component presents a Drain to Source resistance of 85Ohm. Its conductivity is 4-bit.

DG441DYZ Features


1 Channels
15μA Supply Current
Drain-to-Source resistance: 85Ohm
4-Bit

DG441DYZ Applications


There are a lot of Intersil (Renesas Electronics America) DG441DYZ Analog Switches & Multiplexers ICs applications.

  • Cable PC
  • Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
  • Signal routing between systems
  • T1/E1 Terminals
  • Digital cross connects (DSX-1)
  • Microprocessor controlled systems
  • Communication systems
  • Sample hold systems
  • DSUs
  • Intelligent PBX

Write a review

Note: HTML is not translated!
    Bad           Good