DG441DYZ-T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 16 |
| Published | 1999 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 160Ohm |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Operating Supply Voltage | 28V |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 5V |
| Power Dissipation-Max | 1.6mW |
| Operating Supply Current | 15μA |
| Nominal Supply Current | 15μA |
| Number of Bits | 4 |
| Throw Configuration | SPST |
| Turn On Delay Time | 450 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 20V |
| Min Dual Supply Voltage | 5V |
| Off-state Isolation-Nom | 60 dB |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Switch-off Time-Max | 120ns |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
DG441DYZ-T Overview
Due to its SOIC packaging, the electronic part is convenient for international shipping. 16 terminations have been made so far. A electrical component with 1 channels is capable of high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. This digital multiplexer has 160Ohm internal resistance. Datasheets for functions of 16 pins are available. Theswitch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 40V. The analog switch ic is of the Dual, Single supply type and is cost-effective. A low voltage of 5V should be applied to the electronic component. For this digital switch to work, 15μA current would suffice. For this switch, a dual supply voltage is feasible, but it must not exceed 20VThe voltage should be at least 5V if you are using dual power supplies. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. It can operate from 28V operating voltages. An environment with a temperature greater than 85°C should not be used to operate the digital switches. It is able to conduct in a 4-bit way.
DG441DYZ-T Features
1 Channels
15μA Supply Current
4-Bit
DG441DYZ-T Applications
There are a lot of Intersil (Renesas Electronics America) DG441DYZ-T Analog Switches & Multiplexers ICs applications.
- SDH/SONET multiplexers
- FTTH
- Public switching systems
- Routers
- Microwave transmission systems
- Channelized and Unchannelized DS3 applications
- Voice over IP/DSL – Integrated Access Devices, Smart
- Digital Cross-Connects
- PBXs
- Audio and video signal routing
