DG441LDQ-T1-E3

60ns, 35ns SPST - NC 30Ohm Analog Switches BREAK-BEFORE-MAKE DG441 16 Pins 1nA 5V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG441LDQ-T1-E3
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 412
Description: 60ns, 35ns SPST - NC 30Ohm Analog Switches BREAK-BEFORE-MAKE DG441 16 Pins 1nA 5V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Number of Pins	16
Weight	172.98879mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2015
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	35Ohm
Terminal Finish	PURE MATTE TIN
Subcategory	Multiplexer or Switches
Max Power Dissipation	450mW
Technology	BICMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	5V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	DG441
Output	SEPARATE OUTPUT
Pin Count	16
Qualification Status	Not Qualified
Number of Channels	1
Max Supply Voltage	12V
Min Supply Voltage	2.7V
Operating Supply Current	10μA
Power Dissipation	450mW
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	60 ns
Number of Inputs	4
Voltage - Supply, Single/Dual (±)	2.7V~12V ±3V~6V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	35 ns
Max Dual Supply Voltage	6V
-3db Bandwidth	280MHz
On-State Resistance (Max)	30Ohm
Min Dual Supply Voltage	3V
Dual Supply Voltage	5V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	68 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	5pF 6pF
On-state Resistance Match-Nom	0.1Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	60ns, 35ns
Charge Injection	5pC
Channel-to-Channel Matching (ΔRon)	100m Ω
Crosstalk	-95dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	70ns
Drain to Source Resistance	17Ohm
Normal Position	NC
Height	920μm
Length	5.08mm
Width	4.4mm
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant

DG441LDQ-T1-E3 Overview

The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. Operating temperature around -40°C~85°C TA extended. A total of 16 terminations have been recorded. The electronic part delivers high-quality output through its 1 channels. When the electronic component is given a voltage of 5V, it should be turned on and run. This electronic part can be found in the 16 series. On the other hand, analog switches can be constructed using SPST - NC switching circuits. If you are looking for variants of the digital switch, trying search with DG441. The internal resistance of this digital multiplexer is 35Ohm. Datasheets for 16 pin functions are available upon request. The analogue multiplexer in this example is a typical Multiplexer or Switches. A voltage higher than 12V should not normally be supplied to the switches. Analogue multiplexer with a Dual, Single supply type that is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 2.7V. It would be sufficient to run this analogue multiplexer with 10μA current. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. If put voltage greater than 6V on the multiplexer, damage may be caused to the device. You should attach at least 3V voltage if you are using dual power supply. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. Operating the 4 inputs requires 4 inputs. It has a Drain to Source resistance of 17Ohm ohms.