DG441LDY
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 30Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 650mW |
| Technology | BICMOS |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Power Dissipation | 650mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 60 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 35 ns |
| Max Dual Supply Voltage | 6V |
| -3db Bandwidth | 280MHz |
| On-State Resistance (Max) | 30Ohm |
| Min Dual Supply Voltage | 3V |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 6pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 60ns, 35ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -95dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
DG441LDY Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). To ensure high reliability, a new packaging method Tube is used. There is an analog multiplexer mounted in position Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Temperatures around -40°C~85°C TA are extended for operation. A total of 16 terminations have been recorded. As part of the design of the 16 series, this electronic part has been incorporated into the system. Based on SPST - NC switching circuits, these analog multiplexers work. In this multiplexer, the internal resistance is 30Ohm. The functions of 16 pins can be found in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 12V. The analog switch ic is of the Dual, Single supply type and is cost-effective. 2.7V is the lowest voltage the electrical component should receive. The analogue multiplexer may be damaged if voltage is greater than 1μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 6V. With dual power supplies, you should attach at least 3V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. Among the inputs that can be operated are the 4 inputs.
DG441LDY Features
Switch Circuit: SPST - NC
-3db Bandwidth: 280MHz
DG441LDY Applications
There are a lot of Vishay Siliconix DG441LDY Analog Switches & Multiplexers ICs applications.
- Audio and video signal routing
- Cellular phones
- Digital access cross connects
- Imaging
- Fiber In The Loop (FITL)
- Industrial control systems
- Audio/video switches
- Wireless Local Loop
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Battery-powered systems
