DG441LDY-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 35Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 650mW |
| Technology | BICMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG441 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 10μA |
| Power Dissipation | 650mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 60 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 35 ns |
| Max Dual Supply Voltage | 6V |
| -3db Bandwidth | 280MHz |
| On-State Resistance (Max) | 30Ohm |
| Min Dual Supply Voltage | 3V |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 6pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 60ns, 35ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -95dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 70ns |
| Normal Position | NC |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG441LDY-T1-E3 Overview
The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. High reliability is ensured by the advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a number of circuits 1:1. Increasing operating temperature to around -40°C~85°C TA. 16 terminations have been made so far. The electronic part provides high-quality output because it has 1 channels. With a 5V voltage supply, the electrical component should be turned on and run. It is injected into the electrical part body with 16 pins. Based on SPST - NC switching circuits, these analog multiplexers work. DG441 can be used to search for analog multiplexer variants. It has an internal resistance of 35Ohm. Datasheets for 16 pin functions are available upon request. A analogue multiplexer of this type is a Multiplexer or Switches. Multiplexers should not be powered above 12V in normal situations. Analogue multiplexer with a Dual, Single supply type that is cost-effective. It is recommended that the electrical component receives a voltage of 2.7V. This multiplexer would work with 10μA current. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. If put voltage greater than 6V on the multiplexer, damage may be caused to the device. It is recommended that you attach at least 3V to your dual power supply. There are SEPARATE OUTPUT outputs on this analog switch ic. The 4 inputs need to be operated in order to work.
DG441LDY-T1-E3 Features
1 Channels
Switch Circuit: SPST - NC
10μA Supply Current
-3db Bandwidth: 280MHz
DG441LDY-T1-E3 Applications
There are a lot of Vishay Siliconix DG441LDY-T1-E3 Analog Switches & Multiplexers ICs applications.
- Relay Replacement
- Sample-and-hold systems
- Communication systems
- Cable PC
- Avionics
- Power routing
- Battery-powered systems
- Mechanical reed relay replacement
- DVD-R
- Cellular phones
