DG442AK/883B
| Parameters | |
|---|---|
| Switch-on Time-Max | 250ns |
| Switch-off Time-Max | 170ns |
| Normal Position | NC |
| Height Seated (Max) | 5.08mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Factory Lead Time | 1 Week |
| Mounting Type | Through Hole |
| Package / Case | 16-CDIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 85Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 800mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Max Supply Current | 100μA |
| Turn On Delay Time | 400 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4.5V |
| Screening Level | MIL-STD-883 Class B |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 250ns, 170ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω (Max) |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
DG442AK/883B Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-CDIP (0.300, 7.62mm). To ensure high reliability, a new packaging method Tube is used. In Through Hole, this analog switch is mounted. Multiplexer and demultiplexer circuits have a number 1:1. Operating temperature extended to -55°C~125°C TA. In total, there are 16 terminations. By its 1 channels, the electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. Electronic part bodies are injected with 16 pins. Unlike digital switches, these are based on SPST - NO switching circuits. There are 4 circuits in this switch device. It has an internal resistance of 85Ohm. Datasheets for functions of 16 pins are available. This switch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 30V. The digital multiplexer has a low cost Dual, Single supply. There should be 10V voltage fed to the electrical part below 10V. Put voltage above 100μA on the multiplexer to cause damage. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. You should attach at least 4.5V voltage if you are using dual power supply. This analog switch ic utilizes SEPARATE OUTPUT output. There is a voltage range of 28V operating voltages for the electrical part.
DG442AK/883B Features
1 Channels
Switch Circuit: SPST - NO
DG442AK/883B Applications
There are a lot of Maxim Integrated DG442AK/883B Analog Switches & Multiplexers ICs applications.
- E1 Multiplexer
- Microprocessor controlled systems
- High speed data transmission line cards
- Cell phones
- Medical systems
- Signal routing between systems
- Audio/video switches
- Fiber to the Home
- Private Branch Exchange (PBX)
- Data switching
