DG442BDJ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 80Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | DG442 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 13V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 300 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 220ns, 120ns |
| Charge Injection | -1pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 220ns |
| Switch-off Time-Max | 120ns |
| Normal Position | NO |
| Height Seated (Max) | 5.08mm |
| Length | 20.13mm |
| Width | 7.62mm |
| RoHS Status | ROHS3 Compliant |
DG442BDJ Overview
Presented in 16-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. This high-reliability packaging method uses advanced packaging methods Tube. It is mounted in the position Through Hole. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. Totally, there are 16 terminations. As a result of its 1 channels, this electronic component provides high-quality output. A 15V voltage supply should turn on and run the electronic component. An electrical component like this is included in the 16 series. The analog switch ics are built using SPST - NO switching circuits. A total of 4 circuits make up this switch device. Try searching for the analog switch ic with DG442 if you are looking for variants. There is 80Ohm internal resistance in this digital multiplexer. The functions of 16 pins can be found in the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 25V. Analog switch ics with Dual, Single supply type are cost-effective. It is recommended to use 13V as the lowest voltage for the electrical part. When the digital multiplexer is charged above 1μA, damage can occur. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. A dual power supply should have at least 7V voltage attached. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.
DG442BDJ Features
1 Channels
Switch Circuit: SPST - NO
DG442BDJ Applications
There are a lot of Vishay Siliconix DG442BDJ Analog Switches & Multiplexers ICs applications.
- Fiber to the Home
- Precision test equipment
- FTTH
- Relay Replacement
- Video signal routing
- Modems
- Battery Powered Systems
- Fault Tolerant Systems
- High speed data transmission line cards
- Avionics test equipment
