DG442BDJ-E3
| Parameters | |
|---|---|
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | DG442 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 5μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 220ns, 120ns |
| Charge Injection | -1pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 220ns |
| Switch-off Time-Max | 120ns |
| Normal Position | NO |
| Height Seated (Max) | 5.08mm |
| Length | 20.13mm |
| Width | 7.62mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 90Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
DG442BDJ-E3 Overview
The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. High reliability is provided by advanced packaging method Tube. Mounted in Through Hole is this multiplexer. 1:1 is the ratio of multiplexer to demultiplexer circuits. Increasing operating temperature to around -40°C~85°C TA. In total, 16 terminations have occurred. As a result of its 1 channels, this electronic component provides high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. It is injected into the electrical part body with 16 pins. Unlike digital switches, these are based on SPST - NO switching circuits. A 4 circuit is present in this switch device. Use DG442 to search for variants of the digital switches. The internal resistance of this digital multiplexer is 90Ohm. To find out what the 16 pins do, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. Users shouldn't supply more than 25V voltage to the switch device. An effective Dual, Single supply digital multiplexer. 13V is the lowest voltage the electrical component should receive. 5μA current would be enough for this multiplexer to operate. Putting voltage greater than 1μA on the multiplexer may cause damage. There is no problem with using dual supply voltage, but it should not exceed 22V. It is recommended that you attach at least 7V to your dual power supply. There are SEPARATE OUTPUT outputs on this analog switch ic.
DG442BDJ-E3 Features
1 Channels
Switch Circuit: SPST - NO
5μA Supply Current
DG442BDJ-E3 Applications
There are a lot of Vishay Siliconix DG442BDJ-E3 Analog Switches & Multiplexers ICs applications.
- Microwave transmission systems
- Power routing
- SONET
- Avionics test equipment
- Cross Connects
- Medical Instrumentation
- Routers
- RGB switches
- MP3 players
- DSUs
