Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Weight |
665.986997mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2016 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
80Ohm |
Terminal Finish |
TIN LEAD |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
900mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
30 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Number of Channels |
1 |
Max Supply Voltage |
25V |
Min Supply Voltage |
13V |
Power Dissipation |
900mW |
Max Supply Current |
1μA |
Turn On Delay Time |
220 ns |
Number of Inputs |
4 |
Voltage - Supply, Single/Dual (±) |
12V ±15V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
120 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
80Ohm |
Min Dual Supply Voltage |
7V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
4pF 4pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
220ns, 120ns |
Charge Injection |
-1pC |
Channel-to-Channel Matching (ΔRon) |
2 Ω |
Crosstalk |
-95dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NO |
Height |
1.55mm |
Length |
10mm |
Width |
4mm |
RoHS Status |
Non-RoHS Compliant |
DG442BDY Overview
Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. High reliability is provided by advanced packaging method Tube. Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have the same number of circuits 1:1. Operating temperature around -40°C~85°C TA extended. The total number of terminations is 16. A electrical component with 1 channels is capable of high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. The electrical component body receives 16 pins. A SPST - NO switching circuit is used to build these analog multiplexers. An switch multiplexer with 80Ohm internal resistance has a value of 80Ohm. To find out what the 16 pins do, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. It is normally recommended that users do not supply the multiplexer with voltages higher than 25V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. A low voltage of 13V should be applied to the electronic component. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. There is no problem with using dual supply voltage, but it should not exceed 22V. If you are using dual power supplies, you should attach at least 7V. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. The electrical component supports 4 inputs.
DG442BDY Features
1 Channels
Switch Circuit: SPST - NO
DG442BDY Applications
There are a lot of Vishay Siliconix DG442BDY Analog Switches & Multiplexers ICs applications.
- Optical Applications
- Medical systems
- Industrial
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Communication systems
- Multiplexers
- Channel Banks
- Battery Powered Systems
- Residential Gateways, Home Gateway/Router
- Avionics and Military Systems