banner_page

DG442BDY-T1

220ns, 120ns SPST - NO 80Ohm Analog Switches BREAK-BEFORE-MAKE 16 Pins 500pA 15V 16-SOIC (0.154, 3.90mm Width)


  • Manufacturer: Vishay Siliconix
  • Nocochips NO: 880-DG442BDY-T1
  • Package: 16-SOIC (0.154, 3.90mm Width)
  • Datasheet: PDF
  • Stock: 511
  • Description: 220ns, 120ns SPST - NO 80Ohm Analog Switches BREAK-BEFORE-MAKE 16 Pins 500pA 15V 16-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mounting Type Surface Mount
Package / Case 16-SOIC (0.154, 3.90mm Width)
Surface Mount YES
Number of Pins 16
Weight 665.986997mg
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2016
JESD-609 Code e0
Pbfree Code no
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 16
Resistance 80Ohm
Terminal Finish TIN LEAD
Subcategory Multiplexer or Switches
Max Power Dissipation 900mW
Technology CMOS
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 240
Number of Functions 4
Supply Voltage 15V
Terminal Pitch 1.27mm
Reach Compliance Code unknown
Time@Peak Reflow Temperature-Max (s) 30
Output SEPARATE OUTPUT
Pin Count 16
Qualification Status Not Qualified
Number of Channels 1
Number of Circuits 4
Max Supply Voltage 25V
Min Supply Voltage 13V
Max Supply Current 1μA
Turn On Delay Time 220 ns
Voltage - Supply, Single/Dual (±) 12V ±15V
Supply Type Dual, Single
Neg Supply Voltage-Nom (Vsup) -15V
Turn-Off Delay Time 120 ns
Max Dual Supply Voltage 22V
On-State Resistance (Max) 80Ohm
Min Dual Supply Voltage 7V
Dual Supply Voltage 15V
Multiplexer/Demultiplexer Circuit 1:1
Off-state Isolation-Nom 90 dB
Current - Leakage (IS(off)) (Max) 500pA
Channel Capacitance (CS(off), CD(off)) 4pF 4pF
On-state Resistance Match-Nom 2Ohm
Switch Circuit SPST - NO
Switch Time (Ton, Toff) (Max) 220ns, 120ns
Charge Injection -1pC
Channel-to-Channel Matching (ΔRon) 2 Ω
Crosstalk -95dB @ 100kHz
Switching BREAK-BEFORE-MAKE
Normal Position NC
Height 1.55mm
Length 10mm
Width 4mm
RoHS Status Non-RoHS Compliant

DG442BDY-T1 Overview


Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). It is mounted in the position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Extended operating temperature around -40°C~85°C TA. Totally, there are 16 terminations. As a result of its 1 channels, this electronic component provides high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. As part of its design, the 16 series is equipped with this electronic component. These analog multiplexers are built based on SPST - NO switching circuits. A total of 4 circuits make up this switch device. It has an internal resistance of 80Ohm. The functions of 16 pins can be found in the datasheets. Multiplexer or Switches is a typical switch device. normally, users should not supply switches with voltages higher than 25V. A cost-effective Dual, Single supply type analogue multiplexer. There should be 13V voltage fed to the electrical part below 13V. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. Despite this switch device's dual supply capability, its voltage should not exceed 22V. It is recommended that you attach at least 7V to your dual power supply. SEPARATE OUTPUT outputs are utilized by this digital multiplexer.

DG442BDY-T1 Features


1 Channels
Switch Circuit: SPST - NO

DG442BDY-T1 Applications


There are a lot of Vishay Siliconix DG442BDY-T1 Analog Switches & Multiplexers ICs applications.

  • Relay replacements
  • Cellular phones
  • DSUs
  • PCMCIA cards
  • Sample hold systems
  • Ultrasound
  • RGB switches
  • Wireless Local Loop
  • Cable PC
  • Isolation

Write a review

Note: HTML is not translated!
    Bad           Good