DG442BDY-T1-E3

220ns, 120ns SPST - NO 80Ohm Analog Switches BREAK-BEFORE-MAKE DG442 16 Pins 500pA 15V 16-SOIC (0.154, 3.90mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG442BDY-T1-E3
Package: 16-SOIC (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 290
Description: 220ns, 120ns SPST - NO 80Ohm Analog Switches BREAK-BEFORE-MAKE DG442 16 Pins 500pA 15V 16-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SOIC (0.154, 3.90mm Width)
Number of Pins	16
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2016
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	90Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	900mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	15V
Terminal Pitch	1.27mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	DG442
Output	SEPARATE OUTPUT
Pin Count	16
Number of Channels	1
Max Supply Voltage	25V
Min Supply Voltage	13V
Operating Supply Current	5μA
Power Dissipation	900mW
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	300 ns
Number of Inputs	4
Voltage - Supply, Single/Dual (±)	12V ±15V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	200 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	80Ohm
Min Dual Supply Voltage	7V
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	90 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	4pF 4pF
On-state Resistance Match-Nom	2Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	220ns, 120ns
Charge Injection	-1pC
Channel-to-Channel Matching (ΔRon)	2 Ω
Crosstalk	-95dB @ 100kHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	220ns
Switch-off Time-Max	120ns
Normal Position	NC
Height Seated (Max)	1.75mm
Length	9.9mm
Width	3.9mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant

DG442BDY-T1-E3 Overview

Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Operation at a temperature around -40°C~85°C TA. Total terminations are 16. The electronic part delivers high-quality output through its 1 channels. Turning on and running the electrical part should be easy with a 15V voltage supply. There are 16 pins injected into the electronic part body. Unlike digital switches, these are based on SPST - NO switching circuits. Using the DG442 search parameter, you can discover variants of the switch. An switch multiplexer with 90Ohm internal resistance has a value of 90Ohm. Please refer to the datasheets for 16 pins functions. This switch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 25V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. The lowest voltage the electronic part should receive is 13V. 5μA current would be enough for this multiplexer to operate. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. For dual power supplies, a voltage of at least 7V should be attached. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. Among the inputs that can be operated are the 4 inputs.