DG442CJ
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 160Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | DG442 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 15μA |
| Max Supply Current | 100μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 120 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 250ns, 170ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω (Max) |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
DG442CJ Overview
Shipping overseas is convenient due to the electrical component's packing in 16-DIP (0.300, 7.62mm). A high level of reliability can be achieved through the use of an advanced packaging method Tube. This analog switch is mounted in Through Hole. 1:1 is the ratio of multiplexer to demultiplexer circuits. Increasing operating temperature to around 0°C~70°C TA. Totally, there are 16 terminations. By its 1 channels, the electronic component provides high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. A SPST - NO switching circuit is used to build these analog multiplexers. 4 circuits are used in this analogue multiplexer. Try searching with DG442 if you're looking for variants. This digital multiplexer has 160Ohm internal resistance. The datasheets for the 16 pins explain the functions. In this analog multiplexer, the value is Multiplexer or Switches. Users shouldn't supply more than 20V voltage to the switch device. An effective Dual, Single supply digital multiplexer. It is recommended that the electrical component receives a voltage of 4.5V. If put voltage greater than 100μA on the device, damage may be caused to the analogue multiplexer. There is no problem with using dual supply voltage, but it should not exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. The analog switch ic utilizes SEPARATE OUTPUT outputs in total.
DG442CJ Features
1 Channels
Switch Circuit: SPST - NO
DG442CJ Applications
There are a lot of Maxim Integrated DG442CJ Analog Switches & Multiplexers ICs applications.
- Remote wireless modules
- SONET
- Medical systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- DSUs
- Ultrasound
- Data Acquisition Systems
- PDAs
- Relay replacements
- Cell phones
