DG442CY+
| Parameters | |
|---|---|
| Channel-to-Channel Matching (ΔRon) | 4 Ω (Max) |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 85Ohm |
| Terminal Finish | Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG442 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 15μA |
| Max Supply Current | 100μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 120 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 250ns, 170ns |
| Charge Injection | 5pC |
DG442CY+ Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature extended to 0°C~70°C TA. In total, there have been 16 terminations. High-quality output is provided by the electronic component's 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. There is an electrical component included in the 16 series. SPST - NO switching circuits are used in these analog switch ics. The multiplexer consists of 4 circuits. Try searching with DG442 if you're looking for variants. In this multiplexer, the internal resistance is 85Ohm. Please refer to the datasheets for 16 pins functions. The analog multiplexer shown here is a typical Multiplexer or Switches. Multiplexers should not be powered above 20V in normal situations. The digital multiplexer has a low cost Dual, Single supply. There should be 4.5V voltage fed to the electrical part below 4.5V. If put voltage greater than 100μA on the device, damage may be caused to the analogue multiplexer. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. It is recommended that you attach at least 4.5V to your dual power supply. The outputs of this digital multiplexer are SEPARATE OUTPUT in number.
DG442CY+ Features
1 Channels
Switch Circuit: SPST - NO
DG442CY+ Applications
There are a lot of Maxim Integrated DG442CY+ Analog Switches & Multiplexers ICs applications.
- Medical
- Battery Powered Systems
- Data Acquisition Systems
- Precision instrumentation
- E1 Multiplexer
- Precision test equipment
- Switching Systems
- Cell phones
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Cable PC
