DG442DJ

250ns, 170ns SPST - NO 85Ohm Analog Switches BREAK-BEFORE-MAKE DG442 16 Pins 500pA 15V 16-DIP (0.300, 7.62mm)

Manufacturer: Maxim Integrated
Nocochips NO: 503-DG442DJ
Package: 16-DIP (0.300, 7.62mm)
Datasheet: PDF
Stock: 550
Description: 250ns, 170ns SPST - NO 85Ohm Analog Switches BREAK-BEFORE-MAKE DG442 16 Pins 500pA 15V 16-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Mount	Through Hole
Mounting Type	Through Hole
Package / Case	16-DIP (0.300, 7.62mm)
Number of Pins	16
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2009
JESD-609 Code	e0
Pbfree Code	no
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	160Ohm
Terminal Finish	Tin/Lead (Sn85Pb15)
Subcategory	Multiplexer or Switches
Max Power Dissipation	842mW
Technology	CMOS
Peak Reflow Temperature (Cel)	240
Number of Functions	4
Supply Voltage	15V
Time@Peak Reflow Temperature-Max (s)	20
Base Part Number	DG442
Output	SEPARATE OUTPUT
Pin Count	16
Power Supplies	12/+-15V
Number of Channels	4
Max Supply Voltage	30V
Min Supply Voltage	10V
Nominal Supply Current	15μA
Max Supply Current	100μA
Throw Configuration	SPST
Turn On Delay Time	250 ns
Voltage - Supply, Single/Dual (±)	10V~30V ±4.5V~20V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	170 ns
Max Dual Supply Voltage	20V
On-State Resistance (Max)	85Ohm
Min Dual Supply Voltage	4.5V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	60 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	4pF 4pF
On-state Resistance Match-Nom	4Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	250ns, 170ns
Charge Injection	5pC
Channel-to-Channel Matching (ΔRon)	4 Ω (Max)
Crosstalk	-100dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-off Time-Max	120ns
Normal Position	NO
Length	19.175mm
Width	7.62mm
Radiation Hardening	No
RoHS Status	Non-RoHS Compliant
Lead Free	Contains Lead

DG442DJ Overview

Shipping overseas is convenient with the electronic component packed in 16-DIP (0.300, 7.62mm). Advanced packaging method Tube is used to provide high reliability. There is an analog multiplexer mounted in position Through Hole. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. Total terminations are 16. This electronic part offers high-quality output due to its 4 channels. An 15V voltage supply should allow the electrical part to be turned on and run. An electrical component like this is included in the 16 series. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Try searching with DG442 if you're looking for variants. As far as internal resistance is concerned, it has 160Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. Theswitch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 30V in normal situations. Analogue multiplexers of the Dual, Single supply type that are cost-effective. It is recommended that the electrical component receives a voltage of 10V. It may damage the digital multiplexer if the voltage is higher than 100μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. You should attach at least 4.5V voltage if you are using dual power supply. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.