DG442DJ
| Parameters | |
|---|---|
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 85Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Max Supply Current | 100μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 120 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 250ns, 210ns |
| Charge Injection | -1pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω (Max) |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 85Ohm |
| Normal Position | NO |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
DG442DJ Overview
Shipping overseas is convenient due to the electrical component's packing in 16-DIP (0.300, 7.62mm). To ensure high reliability, a new packaging method Tube is used. A switch device like this is mounted in Through Hole. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~85°C TA. A total of 16 terminations have been recorded. Turning on and running the electrical part should be easy with a 15V voltage supply. This electronic part can be found in the 16 series. Circuits based on SPST - NO switching are used to construct these analog switch ics. This multiplexer is composed of 4 circuits. An switch multiplexer with 85Ohm internal resistance has a value of 85Ohm. Datasheets for functions of 16 pins are available. This switch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. The digital multiplexer has a low cost Dual, Single supply. A low voltage of 13V should be applied to the electronic component. When the digital multiplexer is charged above 100μA, damage can occur. Despite this switch device's dual supply capability, its voltage should not exceed 22V. When using dual power supplies, you should attach at least 7V. This analog switch ic utilizes SEPARATE OUTPUT output. Resistivity from Drain to Source is 85Ohm for this electronic part.
DG442DJ Features
Switch Circuit: SPST - NO
Drain-to-Source resistance: 85Ohm
DG442DJ Applications
There are a lot of Vishay Siliconix DG442DJ Analog Switches & Multiplexers ICs applications.
- FTTH
- Multiplexers
- Video switching
- HDTV
- Channel Banks
- Cell phones
- Communication systems
- Relay Replacement
- Cable PC
- Sample-and-hold systems
