DG442DJ-E3

250ns, 210ns SPST - NO 85Ohm Analog Switches BREAK-BEFORE-MAKE DG442 16 Pins 500pA 15V 16-DIP (0.300, 7.62mm)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG442DJ-E3
Package: 16-DIP (0.300, 7.62mm)
Datasheet: PDF
Stock: 332
Description: 250ns, 210ns SPST - NO 85Ohm Analog Switches BREAK-BEFORE-MAKE DG442 16 Pins 500pA 15V 16-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Through Hole
Mounting Type	Through Hole
Package / Case	16-DIP (0.300, 7.62mm)
Number of Pins	16
Weight	1.627801g
Operating Temperature	-40°C~85°C TA
Packaging	Tube
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	85Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	450mW
Technology	CMOS
Number of Functions	4
Supply Voltage	15V
Base Part Number	DG442
Output	SEPARATE OUTPUT
Pin Count	16
Number of Channels	1
Max Supply Voltage	36V
Min Supply Voltage	13V
Operating Supply Current	15μA
Nominal Supply Current	15μA
Power Dissipation	450mW
Max Supply Current	100μA
Throw Configuration	SPST
Turn On Delay Time	250 ns
Number of Inputs	4
Voltage - Supply, Single/Dual (±)	12V ±15V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	120 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	85Ohm
Min Dual Supply Voltage	7V
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	60 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	4pF 4pF
On-state Resistance Match-Nom	4Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	250ns, 210ns
Charge Injection	-1pC
Channel-to-Channel Matching (ΔRon)	4 Ω (Max)
Crosstalk	-100dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-off Time-Max	210ns
Drain to Source Resistance	85Ohm
Normal Position	NO
Height	3.81mm
Length	21.33mm
Width	7.11mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

DG442DJ-E3 Overview

Presented in 16-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tube. Multiplexers like this are mounted in the Through Hole position. Multiplexers and demultiplexers have a ratio of 1:1. Operating temperature around -40°C~85°C TA extended. 16 terminations have been made so far. As a result of its 1 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. It is injected into the electrical part body with 16 pins. These analog multiplexers are built based on SPST - NO switching circuits. Try searching for the analog switch ic with DG442 if you are looking for variants. Internally, this switch multiplexer has a resistance of 85Ohm. Datasheets for 16 pin functions are available upon request. It is a typical Multiplexer or Switches analog multiplexer. normally, users should not supply switches with voltages higher than 36V. An effective Dual, Single supply digital multiplexer. The lowest voltage fed to the electronic component should be 13V. This multiplexer would work with 15μA current. If put voltage greater than 100μA on the device, damage may be caused to the analogue multiplexer. Despite this switch device's dual supply capability, its voltage should not exceed 22V. In the case of dual power supplies, you should connect at least 7V. There are SEPARATE OUTPUT outputs on this analog switch ic. There are 4 inputs to be operated. There is 85Ohm Drain to Source resistance on this electronic part.