DG442DVZ-T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 16 |
| Published | 1999 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 16 |
| Resistance | 160Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Operating Supply Voltage | 28V |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 4 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 15μA |
| Nominal Supply Current | 15μA |
| Max Supply Current | 100μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 450 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 210 ns |
| Max Dual Supply Voltage | 20V |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 18V |
| Off-state Isolation-Nom | 60 dB |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Normal Position | NO |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
DG442DVZ-T Overview
Shipping overseas is convenient with the electronic component packed in TSSOP. There are 16 terminations totally. By its 4 channels, the electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. An switch multiplexer with 160Ohm internal resistance has a value of 160Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. Multiplexer or Switches is a typical switch device. Users should never supply a voltage higher than 40V to a switch device. The digital multiplexer has a low cost Dual, Single supply. 5V is the lowest voltage that should be fed to the electronic electronic part. This digital switch can be operated with a current of 15μA. Putting voltage greater than 100μA on the multiplexer may cause damage. Despite this switch device's dual supply capability, its voltage should not exceed 20V. If you are using a dual power supply, you should attach at least 5V. It can operate from 28V operating voltages. A temperature above 85°C is not suitable for operation of the analogue multiplexer.
DG442DVZ-T Features
4 Channels
15μA Supply Current
DG442DVZ-T Applications
There are a lot of Intersil (Renesas Electronics America) DG442DVZ-T Analog Switches & Multiplexers ICs applications.
- Audio and video signal routing
- High reliability control systems
- Sample hold systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- CSU
- Cable Modem
- Remote wireless modules
- MP3 players
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Optical Applications
