Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Weight |
665.986997mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
1999 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
85Ohm |
Terminal Finish |
Tin/Lead (Sn/Pb) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
900mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Reach Compliance Code |
unknown |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Number of Channels |
4 |
Max Supply Voltage |
36V |
Min Supply Voltage |
13V |
Operating Supply Current |
30mA |
Power Dissipation |
900mW |
Max Supply Current |
100μA |
Throw Configuration |
SPST |
Turn On Delay Time |
250 ns |
Voltage - Supply, Single/Dual (±) |
12V ±15V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
120 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
85Ohm |
Min Dual Supply Voltage |
7V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
4pF 4pF |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
250ns, 210ns |
Charge Injection |
-1pC |
Channel-to-Channel Matching (ΔRon) |
4 Ω (Max) |
Crosstalk |
-100dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
85Ohm |
Normal Position |
NO |
Height |
1.55mm |
Length |
10mm |
Width |
4mm |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Lead Free |
DG442DY Overview
Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tube. The multiplexer is located in Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Increasing operating temperature to around -40°C~85°C TA. 16 terminations have been made so far. A 4 channel electronic part produces high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. A key feature of the 16 series is the inclusion of this electronic part as part of its design. On the other hand, analog switches can be constructed using SPST - NO switching circuits. The internal resistance of this digital multiplexer is 85Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. Users should never supply a voltage higher than 36V to a switch device. Analog switch ics with Dual, Single supply type are cost-effective. 13V is the lowest voltage that should be fed to the electronic electronic part. For this multiplexer to operate, 30mA current would be sufficient. It may damage the digital multiplexer if the voltage is higher than 100μA. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. A dual power supply should have at least 7V voltage attached. This analog switch ic utilizes SEPARATE OUTPUT output. This electronic component presents a Drain to Source resistance of 85Ohm.
DG442DY Features
4 Channels
Switch Circuit: SPST - NO
30mA Supply Current
Drain-to-Source resistance: 85Ohm
DG442DY Applications
There are a lot of Vishay Siliconix DG442DY Analog Switches & Multiplexers ICs applications.
- DVD-R
- Industrial
- Channelized and Unchannelized DS3 applications
- CSU
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Communications systems
- Central office
- Intelligent PBX
- Microwave transmission systems
- Residential Gateways, Home Gateway/Router