DG442DY-E3

250ns, 210ns SPST - NO 85Ohm Analog Switches BREAK-BEFORE-MAKE DG442 16 Pins 500pA 15V 16-SOIC (0.154, 3.90mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG442DY-E3
Package: 16-SOIC (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 780
Description: 250ns, 210ns SPST - NO 85Ohm Analog Switches BREAK-BEFORE-MAKE DG442 16 Pins 500pA 15V 16-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SOIC (0.154, 3.90mm Width)
Number of Pins	16
Weight	665.986997mg
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2007
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	85Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	900mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	15V
Terminal Pitch	1.27mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	DG442
Output	SEPARATE OUTPUT
Pin Count	16
Number of Channels	1
Voltage	12V
Max Supply Voltage	36V
Min Supply Voltage	13V
Operating Supply Current	15μA
Nominal Supply Current	15μA
Power Dissipation	900mW
Max Supply Current	100μA
Throw Configuration	SPST
Turn On Delay Time	250 ns
Number of Inputs	4
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	120 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	85Ohm
Min Dual Supply Voltage	7V
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	60 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	4pF 4pF
On-state Resistance Match-Nom	4Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	250ns, 210ns
Charge Injection	-1pC
Channel-to-Channel Matching (ΔRon)	4 Ω (Max)
Crosstalk	-100dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-off Time-Max	210ns
Drain to Source Resistance	85Ohm
Normal Position	NO
Voltage - Supply, Dual (V±)	±15V
Height	1.55mm
Length	10mm
Width	4mm
Radiation Hardening	No
REACH SVHC	No SVHC
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

DG442DY-E3 Overview

Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Tube is used. It is mounted in the position Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. Operating temperature around -40°C~85°C TA extended. Total terminations are 16. The electronic part delivers high-quality output through its 1 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. A total of 16 pins are injected into the body of the electronic part. Circuits based on SPST - NO switching are used to construct these analog switch ics. Try searching for the analog switch ic with DG442 if you are looking for variants. The internal resistance of this digital multiplexer is 85Ohm. For functions related to 16 pins, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. Users shouldn't supply more than 36V voltage to the switch device. Analogue multiplexers of the Dual, Single supply type that are cost-effective. There should be 13V voltage fed to the electrical part below 13V. The analogue multiplexer could operate on 15μA current. A voltage higher than 100μA may cause damage to the switch multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. If you are using dual power supplies, you should attach at least 7V. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. Operating 4 inputs is required. A Drain to Source resistance of 85Ohm is shown for this electronic part.