DG442DY-T1
| Parameters | |
|---|---|
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Power Dissipation | 900mW |
| Max Supply Current | 100μA |
| Turn On Delay Time | 250 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 120 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 250ns, 210ns |
| Charge Injection | -1pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω (Max) |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 210ns |
| Normal Position | NO |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 85Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 900mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG442 |
DG442DY-T1 Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have the same number of circuits 1:1. Operation at a temperature around -40°C~85°C TA. Total terminations are 16. This electronic part offers high-quality output due to its 1 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. There are 16 pins injected into the electronic part body. A SPST - NO switching circuit is used for these analog switches. Using the DG442 search parameter, you can discover variants of the switch. A 85Ohm internal resistance characterizes this multiplexer. To find out what the functions of 16 pins are, please refer to their datasheets. This switch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. The analog switch ic is of the Dual, Single supply type and is cost-effective. 13V should be the lowest voltage fed to the electronic component. The analogue multiplexer may be damaged if voltage is greater than 100μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. When using dual power supplies, you should attach at least 7V. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. There are 4 inputs to be operated.
DG442DY-T1 Features
1 Channels
Switch Circuit: SPST - NO
DG442DY-T1 Applications
There are a lot of Vishay Siliconix DG442DY-T1 Analog Switches & Multiplexers ICs applications.
- E1 Network Equipment
- Imaging
- 65 V DACs
- Public switching systems
- Remote Powered Equipment
- Transmit
- Battery Powered Instruments
- Sample hold systems
- High-Voltage
- Multi-Line E1 Interface Cards
