banner_page

DG442DYZ

Analog Switches BREAK-BEFORE-MAKE 15V SOIC


  • Manufacturer: Intersil (Renesas Electronics America)
  • Nocochips NO: 391-DG442DYZ
  • Package: SOIC
  • Datasheet: PDF
  • Stock: 473
  • Description: Analog Switches BREAK-BEFORE-MAKE 15V SOIC(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Surface Mount
Package / Case SOIC
Number of Pins 16
Packaging Bulk
Published 1999
JESD-609 Code e3
Part Status Active
Moisture Sensitivity Level (MSL) 3
Number of Terminations 16
ECCN Code EAR99
Resistance 85Ohm
Terminal Finish Matte Tin (Sn) - annealed
Max Operating Temperature 85°C
Min Operating Temperature -40°C
Subcategory Multiplexer or Switches
Technology CMOS
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 4
Supply Voltage 15V
Terminal Pitch 1.27mm
Time@Peak Reflow Temperature-Max (s) 30
Output SEPARATE OUTPUT
Temperature Grade INDUSTRIAL
Number of Channels 1
Max Supply Voltage 40V
Min Supply Voltage 5V
Operating Supply Current 15μA
Nominal Supply Current 15μA
Max Supply Current 100μA
Number of Bits 4
Throw Configuration SPST
Turn On Delay Time 250 ns
Supply Type Dual, Single
Neg Supply Voltage-Nom (Vsup) -15V
Turn-Off Delay Time 120 ns
Max Dual Supply Voltage 20V
Min Dual Supply Voltage 5V
Off-state Isolation-Nom 60 dB
Switching BREAK-BEFORE-MAKE
Switch-off Time-Max 210ns
Drain to Source Resistance 50mOhm
Normal Position NO
Height Seated (Max) 1.75mm
Length 9.9mm
Width 3.9mm
Radiation Hardening No
REACH SVHC No SVHC
RoHS Status RoHS Compliant
Lead Free Lead Free

DG442DYZ Overview


Packed in SOIC, the electronic component is convenient for shipping overseas. The advanced packaging method Bulk provides high reliability. Total terminations are 16. The electronic part provides high-quality output because it has 1 channels. With a 15V voltage supply, the electrical component should be turned on and run. The internal resistance of this digital multiplexer is 85Ohm. Datasheets for 16 pin functions are available upon request. In this analog multiplexer, the value is Multiplexer or Switches. Users should never supply a voltage higher than 40V to a switch device. A cost-effective Dual, Single supply type analogue multiplexer. There should be 5V voltage fed to the electrical part below 5V. The analogue multiplexer could operate on 15μA current. Putting voltage greater than 100μA on the multiplexer may cause damage. There is no problem with using dual supply voltage, but it should not exceed 20V. For dual power supplies, a voltage of at least 5V should be attached. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. Temperatures over 85°C should not be allowed for the multiplexer to operate. There is 50mOhm Drain to Source resistance on this electronic part. It can conduct in a 4-bit manner.

DG442DYZ Features


1 Channels
15μA Supply Current
Drain-to-Source resistance: 50mOhm
4-Bit

DG442DYZ Applications


There are a lot of Intersil (Renesas Electronics America) DG442DYZ Analog Switches & Multiplexers ICs applications.

  • Channelized and Unchannelized DS3 applications
  • Digital cross connects (DSX-1)
  • HDTV
  • PCMCIA cards
  • Audio signal routing
  • Audio and video signal routing
  • Signal routing between systems
  • Modems
  • Cable Telephony – NIU, Set-Top Box, Home Side Box
  • DSLAMs

Write a review

Note: HTML is not translated!
    Bad           Good