DG442DYZ-T
| Parameters | |
|---|---|
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 16 |
| Published | 1999 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 160Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Operating Supply Voltage | 28V |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 15μA |
| Nominal Supply Current | 15μA |
| Max Supply Current | 100μA |
| Number of Bits | 4 |
| Throw Configuration | SPST |
| Turn On Delay Time | 450 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 210 ns |
| Max Dual Supply Voltage | 20V |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 18V |
| Off-state Isolation-Nom | 60 dB |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
DG442DYZ-T Overview
The electronic part can be shipped overseas conveniently because it is packaged in SOIC. The total number of terminations is 16. A 1 channel electronic part produces high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. An switch multiplexer with 160Ohm internal resistance has a value of 160Ohm. For details about the functions of 16 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. Multiplexers should not be powered above 40V in normal situations. Analogue multiplexer with a Dual, Single supply type that is cost-effective. 5V should be the lowest voltage fed to the electronic component. It would be sufficient to run this analogue multiplexer with 15μA current. The analogue multiplexer may be damaged if voltage is greater than 100μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. If you are using dual power supplies, you should attach at least 5V. It can operate from 28V operating voltages. Temperatures above 85°C should not be used to operate the switches. The switch device is capable of conducting in a 4-bit mode.
DG442DYZ-T Features
1 Channels
15μA Supply Current
4-Bit
DG442DYZ-T Applications
There are a lot of Intersil (Renesas Electronics America) DG442DYZ-T Analog Switches & Multiplexers ICs applications.
- Video switching
- Channel Banks
- Optical Applications
- Power routing
- Wireless Local Loop
- Relay Replacement
- Intelligent PBX
- Automatic test equipment
- Battery Powered Systems
- Fault Tolerant Systems
