DG442ETE+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WQFN Exposed Pad |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 160Ohm |
| Terminal Finish | TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 2.667W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.8mm |
| Base Part Number | DG442 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Nominal Supply Current | 15μA |
| Max Supply Current | 100μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 400 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 250ns, 170ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω (Max) |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Switch-off Time-Max | 120ns |
| Normal Position | NO |
| Height Seated (Max) | 0.8mm |
| Length | 5mm |
| Width | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG442ETE+T Overview
The electrical component comes in 16-WQFN Exposed Pad packaging, which makes it convenient to ship overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Increasing operating temperature to around -40°C~85°C TA. In total, there are 16 terminations. This electronic part offers high-quality output due to its 1 channels. A 15V voltage supply should turn on and run the electronic component. There is an electrical component included in the 16 series. Unlike digital switches, these are based on SPST - NO switching circuits. It consists of 4 circuits. Try searching for the analog switch ic with DG442 if you are looking for variants. There is 160Ohm internal resistance in this digital multiplexer. The functions of 16 pins can be found in the datasheets. Multiplexer or Switches is a typical switch device. It is normally recommended that users do not supply the multiplexer with voltages higher than 30V. An effective Dual, Single supply digital multiplexer. In order for the electronic part to function properly, the lowest voltage should be 10V. A voltage higher than 100μA may cause damage to the switch multiplexer. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. A dual power supply should have at least 4.5V voltage attached. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. The electrical part can be operated at 28V voltage levels.
DG442ETE+T Features
1 Channels
Switch Circuit: SPST - NO
DG442ETE+T Applications
There are a lot of Maxim Integrated DG442ETE+T Analog Switches & Multiplexers ICs applications.
- Frame Relay Equipment
- Private Branch Exchange (PBX)
- Industrial and process control systems
- Central office
- High reliability control systems
- Channel Banks
- DVD-R
- Channelized and Unchannelized DS3 applications
- Battery Powered Systems
- E1 Network Equipment
