DG442LDJ-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Supplier Device Package | 16-DIP |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 35Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Base Part Number | DG442 |
| Number of Outputs | 4 |
| Number of Channels | 4 |
| Number of Circuits | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 10μA |
| Max Supply Current | 100μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 136 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 6V |
| -3db Bandwidth | 280MHz |
| On-State Resistance (Max) | 30Ohm |
| Min Dual Supply Voltage | 3V |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 6pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 60ns, 35ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 100mOhm |
| Crosstalk | -95dB @ 1MHz |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| RoHS Status | ROHS3 Compliant |
DG442LDJ-E3 Overview
The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. Advanced packaging method Tube is used to provide high reliability. In Through Hole, this analog switch is mounted. Multiplexers and demultiplexers have the same number of circuits 1:1. Operation at a temperature around -40°C~85°C TA. A electrical component with 4 channels is capable of high-quality output. A SPST - NO switching circuit is used to build these analog multiplexers. A 4 circuit is present in this switch device. If you are looking for variants of the digital switch, trying search with DG442. Analog switches have 35Ohm internal resistance. Datasheets for 16 pin functions are available upon request. In a normalsituation, users should not supply the switches with voltage higher than 12V. An effective Dual, Single supply digital multiplexer. 2.7V is the lowest voltage the electrical component should receive. This multiplexer would work with 10μA current. Put voltage above 100μA on the multiplexer to cause damage. There is no problem with using dual supply voltage, but it should not exceed 6V. In the case of dual power supplies, you should connect at least 3V. Operating the 4 inputs requires 4 inputs. The switches should not operate in an environment where the temperature is higher than 85°C. There are 4 outputs on the analogue multiplexer. There is a 16-DIP package available from suppliers.
DG442LDJ-E3 Features
4 Channels
Switch Circuit: SPST - NO
10μA Supply Current
-3db Bandwidth: 280MHz
DG442LDJ-E3 Applications
There are a lot of Vishay Siliconix DG442LDJ-E3 Analog Switches & Multiplexers ICs applications.
- Digital Cross-Connects
- Video signal routing
- Fiber to the Home
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Fault Tolerant Systems
- Medical Instrumentation
- Cellular phones
- Modems
- Channel Banks
- SDH
