DG442LDQ-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Supplier Device Package | 16-TSSOP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2013 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 35Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Base Part Number | DG442 |
| Number of Circuits | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 10μA |
| Throw Configuration | SPST |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Max Dual Supply Voltage | 6V |
| -3db Bandwidth | 280MHz |
| On-State Resistance (Max) | 30Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 6pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 60ns, 35ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 100mOhm |
| Crosstalk | -95dB @ 1MHz |
| RoHS Status | ROHS3 Compliant |
DG442LDQ-E3 Overview
Shipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). In order to provide high reliability, an advanced packaging method Tube is used. The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operation at a temperature around -40°C~85°C TA. Based on SPST - NO switching circuits, these analog multiplexers work. The multiplexer consists of 4 circuits. Try searching with DG442 to find analog multiplexer variants. In this multiplexer, the internal resistance is 35Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. In normalcircumstances, users should not exceed 12V volts for the multiplexer. A cost-effective Dual, Single supply type analogue multiplexer. 2.7V should be the lowest voltage fed to the electronic component. 10μA current would be enough for this multiplexer to operate. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 6V. You should attach at least 3V voltage if you are using dual power supply. The switches should not operate in an environment where the temperature is higher than 85°C. It is possible to purchase a 16-TSSOP package from suppliers.
DG442LDQ-E3 Features
Switch Circuit: SPST - NO
10μA Supply Current
-3db Bandwidth: 280MHz
DG442LDQ-E3 Applications
There are a lot of Vishay Siliconix DG442LDQ-E3 Analog Switches & Multiplexers ICs applications.
- Battery-powered systems
- High speed data transmission line cards
- Precision instrumentation
- MP3 players
- Routers
- Fault Tolerant Systems
- Multi-Line E1 Interface Cards
- Channelized and Unchannelized DS3 applications
- Mechanical reed relay replacement
- DSLAMs
