DG442LDY-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 33Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | ALSO OPERATES WITH 2.7V TO 12V SINGLE SUPPLY |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 650mW |
| Technology | BICMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG442 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 10μA |
| Power Dissipation | 650mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 60 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 35 ns |
| Max Dual Supply Voltage | 6V |
| -3db Bandwidth | 280MHz |
| On-State Resistance (Max) | 30Ohm |
| Min Dual Supply Voltage | 3V |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 6pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 60ns, 35ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -95dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 17Ohm |
| Normal Position | NO |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG442LDY-E3 Overview
This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. This packaging method provides high reliability because it uses advanced packaging techniques. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, there have been 16 terminations. As a result of its 1 channels, this electronic component provides high-quality output. If the voltage supply is 5V volts, the electrical component should be turned on and run. It is part of the design of the 16 series that this electronic component is included. Unlike digital switches, these are based on SPST - NO switching circuits. If you are looking for variants of the digital switch, trying search with DG442. It has an internal resistance of 33Ohm. The datasheets for the 16 pins explain the functions. It is a typical Multiplexer or Switches analog multiplexer. Users shouldn't supply more than 12V voltage to the switch device. Analogue multiplexers of the Dual, Single supply type that are cost-effective. The lowest voltage fed to the electronic component should be 2.7V. For this multiplexer to operate, 10μA current would be sufficient. The analogue multiplexer may be damaged if voltage is greater than 1μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 6V. If you are using dual power supplies, you should attach at least 3V. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. It is possible to operate 4 inputs. Don’t miss additional features of the electronic component such as: ALSO OPERATES WITH 2.7V TO 12V SINGLE SUPPLY. Drain to Source resistance for this electronic component is 17Ohm.
DG442LDY-E3 Features
1 Channels
Switch Circuit: SPST - NO
10μA Supply Current
-3db Bandwidth: 280MHz
Additional Features: ALSO OPERATES WITH 2.7V TO 12V SINGLE SUPPLY
Drain-to-Source resistance: 17Ohm
DG442LDY-E3 Applications
There are a lot of Vishay Siliconix DG442LDY-E3 Analog Switches & Multiplexers ICs applications.
- Audio/video switches
- Digital cross connects (DSX-1)
- Microwave transmission systems
- Industrial
- Imaging
- CSU
- SONET/SDH ADM
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Cable PC
- Multiplexers
