DG442LDY-T1
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 30Ohm |
| Terminal Finish | TIN LEAD |
| Additional Feature | ALSO OPERATES WITH 2.7V TO 12V SINGLE SUPPLY |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 650mW |
| Technology | BICMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 60 ns |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 35 ns |
| Max Dual Supply Voltage | 6V |
| -3db Bandwidth | 280MHz |
| On-State Resistance (Max) | 30Ohm |
| Min Dual Supply Voltage | 3V |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 6pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 60ns, 35ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -95dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
DG442LDY-T1 Overview
Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 16. By its 1 channels, the electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 5V voltage supply. An injection of 16 pins is performed into the body of the electrical component. A SPST - NO switching circuit is used to build these analog multiplexers. It consists of 4 circuits. In this multiplexer, the internal resistance is 30Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. Multiplexers should not be powered above 12V in normal situations. An effective Dual, Single supply digital multiplexer. 2.7V should be the lowest voltage fed to the electronic component. A voltage higher than 1μA may cause damage to the switch multiplexer. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 6V. You should attach at least 3V voltage if you are using dual power supply. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. Additional features include: ALSO OPERATES WITH 2.7V TO 12V SINGLE SUPPLY.
DG442LDY-T1 Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 280MHz
Additional Features: ALSO OPERATES WITH 2.7V TO 12V SINGLE SUPPLY
DG442LDY-T1 Applications
There are a lot of Vishay Siliconix DG442LDY-T1 Analog Switches & Multiplexers ICs applications.
- Multi-Line E1 Interface Cards
- Communication systems
- Industrial
- Modems
- Fiber In The Loop (FITL)
- Data switching
- SONET
- RGB switches
- DSLAMs
- Audio signal routing
