DG442LDY-T1-E3

60ns, 35ns SPST - NO 30Ohm Analog Switches BREAK-BEFORE-MAKE DG442 16 Pins 1nA 5V 16-SOIC (0.154, 3.90mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG442LDY-T1-E3
Package: 16-SOIC (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 995
Description: 60ns, 35ns SPST - NO 30Ohm Analog Switches BREAK-BEFORE-MAKE DG442 16 Pins 1nA 5V 16-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Contact Plating	Tin
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SOIC (0.154, 3.90mm Width)
Number of Pins	16
Weight	665.986997mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2013
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	35Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	650mW
Technology	BICMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	5V
Terminal Pitch	1.27mm
Reach Compliance Code	unknown
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG442
Pin Count	16
Qualification Status	Not Qualified
Polarity	Non-Inverting
Number of Channels	1
Max Supply Voltage	12V
Min Supply Voltage	2.7V
Operating Supply Current	10μA
Power Dissipation	650mW
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	60 ns
Number of Inputs	4
Voltage - Supply, Single/Dual (±)	2.7V~12V ±3V~6V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	35 ns
Max Dual Supply Voltage	6V
-3db Bandwidth	280MHz
On-State Resistance (Max)	30Ohm
Min Dual Supply Voltage	3V
High Level Output Current	30mA
Dual Supply Voltage	5V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	68 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	5pF 6pF
On-state Resistance Match-Nom	0.1Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	60ns, 35ns
Charge Injection	5pC
Channel-to-Channel Matching (ΔRon)	100m Ω
Crosstalk	-95dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	70ns
Normal Position	NO
Height	1.55mm
Length	10mm
Width	4mm
RoHS Status	ROHS3 Compliant

DG442LDY-T1-E3 Overview

Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. The operating temperature is extended to around -40°C~85°C TA. 16 terminations have been made so far. Due to its 1 channels, the electrical component produces high-quality output. If the voltage supply is 5V volts, the electrical component should be turned on and run. It is injected into the electrical part body with 16 pins. The analog switch ics are built using SPST - NO switching circuits. Look for analog switch ic variants by searching with DG442. In this multiplexer, the internal resistance is 35Ohm. For details about the functions of 16 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Users should never supply a voltage higher than 12V to a switch device. Analog switch ics with Dual, Single supply type are cost-effective. It is recommended that the electrical component receives a voltage of 2.7V. In order to operate this switch device, it would need a current of 10μA. The analogue multiplexer may be damaged if voltage is greater than 1μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 6V. You should attach at least 3V voltage if you are using dual power supply. There are 4 inputs to be operated.