Parameters |
Max Supply Current |
1μA |
Turn On Delay Time |
300 ns |
Number of Inputs |
4 |
Voltage - Supply, Single/Dual (±) |
12V ±15V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
200 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
80Ohm |
Min Dual Supply Voltage |
7V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
5pF 5pF |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
300ns, 200ns |
Charge Injection |
1pC |
Crosstalk |
-95dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NC |
Height Seated (Max) |
5.08mm |
Length |
20.13mm |
Width |
7.62mm |
RoHS Status |
ROHS3 Compliant |
Mount |
Through Hole |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
80Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
470mW |
Technology |
CMOS |
Peak Reflow Temperature (Cel) |
NOT SPECIFIED |
Number of Functions |
4 |
Supply Voltage |
15V |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
NOT SPECIFIED |
Base Part Number |
DG444 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Number of Channels |
1 |
Max Supply Voltage |
36V |
Min Supply Voltage |
13V |
Power Dissipation |
470mW |
DG444BDJ Overview
Shipping overseas is convenient with the electronic component packed in 16-DIP (0.300, 7.62mm). High reliability is ensured by the advanced packaging method Tube. There is an analog multiplexer mounted in position Through Hole. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Extended operating temperature around -40°C~85°C TA. In total, there have been 16 terminations. The electronic part delivers high-quality output through its 1 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. There is an electrical component included in the 16 series. Unlike digital switches, these are based on SPST - NC switching circuits. Use DG444 to search for variants of the digital switches. In this multiplexer, the internal resistance is 80Ohm. You can find the functions of the 16 pins in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Users should never supply a voltage higher than 36V to a switch device. The digital multiplexer has a low cost Dual, Single supply. 13V should be the lowest voltage fed to the electronic component. Putting voltage greater than 1μA on the multiplexer may cause damage. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. For dual power supplies, a voltage of at least 7V should be attached. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. The 4 inputs need to be operated in order to work.
DG444BDJ Features
1 Channels
Switch Circuit: SPST - NC
DG444BDJ Applications
There are a lot of Vishay Siliconix DG444BDJ Analog Switches & Multiplexers ICs applications.
- Industrial control systems
- FTTH
- Ultrasound
- Cable Modem
- Audio/video switches
- Fiber to the Home
- PDAs
- Public switching systems
- Power routing
- Cellular phones