DG444BDJ-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 160Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | DG444 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 5μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 300ns, 200ns |
| Charge Injection | 1pC |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height Seated (Max) | 5.08mm |
| Length | 20.13mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG444BDJ-E3 Overview
Due to its 16-DIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. High reliability is achieved by using advanced packaging method Tube. The multiplexer is located in Through Hole. Multiplexers and demultiplexers have the same number of circuits 1:1. Operational temperature extended around -40°C~85°C TA. The total number of terminations is 16. As a result of its 1 channels, this electronic component provides high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. Electronic part bodies are injected with 16 pins. A SPST - NC switching circuit is used for these analog switches. It consists of 4 circuits. Try searching with DG444 if you're looking for variants. Internally, this switch multiplexer has a resistance of 160Ohm. For functions related to 16 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. In a normalsituation, users should not supply the switches with voltage higher than 36V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. 13V is the lowest voltage the electrical component should receive. An operating current of 5μA would be sufficient for this switch device. A voltage higher than 1μA may cause damage to the switch multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. If you are using a dual power supply, you should attach at least 7V. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.
DG444BDJ-E3 Features
1 Channels
Switch Circuit: SPST - NC
5μA Supply Current
DG444BDJ-E3 Applications
There are a lot of Vishay Siliconix DG444BDJ-E3 Analog Switches & Multiplexers ICs applications.
- Public switching systems
- Medical systems
- Optical Applications
- Microwave transmission systems
- Microprocessor Controlled Analog Systems
- Battery Powered Instruments
- Frame Relay Equipment
- Battery Powered Systems
- FTTH
- Automotive applications
