DG444BDN-T1-E4

300ns, 200ns SPST - NC 80Ohm QUAD Analog Switches BREAK-BEFORE-MAKE DG444 16 Pins 500pA 15V 16-VQFN Exposed Pad

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG444BDN-T1-E4
Package: 16-VQFN Exposed Pad
Datasheet: PDF
Stock: 100
Description: 300ns, 200ns SPST - NC 80Ohm QUAD Analog Switches BREAK-BEFORE-MAKE DG444 16 Pins 500pA 15V 16-VQFN Exposed Pad(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-VQFN Exposed Pad
Number of Pins	16
Weight	57.09594mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2013
JESD-609 Code	e4
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	160Ohm
Terminal Finish	PALLADIUM GOLD OVER NICKEL
Subcategory	Multiplexer or Switches
Max Power Dissipation	850mW
Technology	CMOS
Terminal Position	QUAD
Terminal Form	NO LEAD
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	15V
Terminal Pitch	0.65mm
Reach Compliance Code	unknown
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	DG444
Output	SEPARATE OUTPUT
Pin Count	16
Qualification Status	Not Qualified
Number of Channels	1
Number of Circuits	4
Max Supply Voltage	36V
Min Supply Voltage	13V
Operating Supply Current	5μA
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	300 ns
Voltage - Supply, Single/Dual (±)	12V ±15V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	200 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	80Ohm
Min Dual Supply Voltage	7V
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	90 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	5pF 5pF
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	300ns, 200ns
Charge Injection	1pC
Crosstalk	-95dB @ 100kHz
Switching	BREAK-BEFORE-MAKE
Normal Position	NC
Height Seated (Max)	1mm
RoHS Status	ROHS3 Compliant

DG444BDN-T1-E4 Overview

Shipping overseas is convenient with the electronic component packed in 16-VQFN Exposed Pad. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 16. High-quality output is provided by the electronic component's 1 channels. Turning on and running the electrical part should be easy with a 15V voltage supply. There is an electrical component included in the 16 series. A SPST - NC switching circuit is used to build these analog multiplexers. Circuits number 4 make up this analogue multiplexer. Look for analog switch ic variants by searching with DG444. Internally, this switch multiplexer has a resistance of 160Ohm. Datasheets for 16 pin functions are available upon request. There is a standard Multiplexer or Switches analogue multiplexer here. A voltage higher than 36V should not normally be supplied to the switches. Analogue multiplexers of the Dual, Single supply type that are cost-effective. 13V is the lowest voltage the electrical component should receive. For this multiplexer to operate, 5μA current would be sufficient. A digital multiplexer may suffer damage if voltage is applied above 1μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. If you are using dual power supplies, you should attach at least 7V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.