DG444BDY
| Parameters | |
|---|---|
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 300ns, 200ns |
| Charge Injection | 1pC |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 80Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 300 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
DG444BDY Overview
Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tube. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Operation at a temperature around -40°C~85°C TA. Total terminations are 16. A high-quality output is provided by the electrical component's 1 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. This electrical component is included in the 16 series of products. SPST - NC switching circuits are used in these analog switch ics. A 4 circuit is present in this switch device. Analog switches have 80Ohm internal resistance. For functions related to 16 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. In a normalsituation, users should not supply the switches with voltage higher than 36V. Analog switch ics with Dual, Single supply type are cost-effective. There should be 13V voltage fed to the electrical part below 13V. The analogue multiplexer may be damaged if voltage is greater than 1μA. Despite this switch's dual supply capability, its voltage should not exceed 22V. If you are using dual power supplies, you should attach at least 7V. This analog switch ic utilizes SEPARATE OUTPUT output.
DG444BDY Features
1 Channels
Switch Circuit: SPST - NC
DG444BDY Applications
There are a lot of Vishay Siliconix DG444BDY Analog Switches & Multiplexers ICs applications.
- Medical
- MP3 players
- Medical systems
- Central office
- Digital access cross connects
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- DSLAMs
- PBX interfaces
- USB 1.1 signal switching circuits
- Fault Tolerant Systems
