DG444BDY-T1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 80Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
| Output | SEPARATE OUTPUT |
| Qualification Status | Not Qualified |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Analog IC - Other Type | DPDT |
| Power Dissipation | 640mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 300 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 300ns, 200ns |
| Charge Injection | 1pC |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
DG444BDY-T1 Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. High reliability is ensured by the advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Around -40°C~85°C TA is the extended operating temperature. 16 terminations have been made so far. SPST - NC switching circuits are used in these analog switch ics. It has an internal resistance of 80Ohm. To find out what the 16 pins do, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. Users should never supply a voltage higher than 36V to a switch device. Dual, Single supply type digital switch with a low cost. In order for the electronic part to function properly, the lowest voltage should be 13V. A voltage higher than 1μA may cause damage to the switch multiplexer. For this switch, a dual supply voltage is feasible, but it must not exceed 22VIf you are using dual power supplies, you should attach at least 7V. There is an analog IC DPDT integrated with this board. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. Among the inputs that can be operated are the 4 inputs.
DG444BDY-T1 Features
Switch Circuit: SPST - NC
DG444BDY-T1 Applications
There are a lot of Vishay Siliconix DG444BDY-T1 Analog Switches & Multiplexers ICs applications.
- Medical
- SDH
- HDTV
- Cross Connects
- Audio signal routing
- Communication systems
- Multiplexers
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Automotive applications
- Battery Powered Systems
