DG444BDY-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 160Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG444 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 5μA |
| Power Dissipation | 640mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 300ns, 200ns |
| Charge Injection | 1pC |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG444BDY-T1-E3 Overview
Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. High reliability is provided by advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Operational temperature extended around -40°C~85°C TA. Totally, there are 16 terminations. A electrical component with 1 channels is capable of high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. An injection of 16 pins is performed into the body of the electrical component. A SPST - NC switching circuit is used for these analog switches. Try searching for the analog switch ic with DG444 if you are looking for variants. A 160Ohm internal resistance characterizes this multiplexer. Datasheets for functions of 16 pins are available. The analog multiplexer shown here is a typical Multiplexer or Switches. Multiplexers should not be powered above 36V in normal situations. The digital multiplexer has a low cost Dual, Single supply. It is recommended to use 13V as the lowest voltage for the electrical part. For this digital switch to work, 5μA current would suffice. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. For dual power supplies, a voltage of at least 7V should be attached. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. Operating the 4 inputs requires 4 inputs.
DG444BDY-T1-E3 Features
1 Channels
Switch Circuit: SPST - NC
5μA Supply Current
DG444BDY-T1-E3 Applications
There are a lot of Vishay Siliconix DG444BDY-T1-E3 Analog Switches & Multiplexers ICs applications.
- Digital access cross connects
- Avionics test equipment
- Channel Banks
- Microprocessor Controlled Analog Systems
- HDTV
- Routers
- Transmit
- Residential Gateways, Home Gateway/Router
- Intelligent PBX
- Cross Connects
