DG444DJ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 85Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Reach Compliance Code | unknown |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Power Supplies | 512/+-15V |
| Number of Channels | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 30mA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 450mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 5V~36V ±5V~20V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 140 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 20V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 250ns, 140ns |
| Charge Injection | -1pC |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 50Ohm |
| Normal Position | NC |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Lead Free |
DG444DJ Overview
Shipping overseas is convenient due to the electrical component's packing in 16-DIP (0.300, 7.62mm). This high-reliability packaging method uses advanced packaging methods Tube. A switch device like this is mounted in Through Hole. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operating temperature around -40°C~85°C TA extended. In total, there have been 16 terminations. A 4 channel electronic part produces high-quality output. The electronic part body is injected with 16 pins. A SPST - NC switching circuit is used for these analog switches. Internally, this switch multiplexer has a resistance of 85Ohm. Please refer to the datasheets for 16 pins functions. A analogue multiplexer of this type is a Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. Analog switch ics with Dual, Single supply type are cost-effective. It is recommended to use 13V as the lowest voltage for the electrical part. This digital switch can be operated with a current of 30mA. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. Despite this switch's dual supply capability, its voltage should not exceed 22V. For dual power supplies, a voltage of at least 7V should be attached. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. The Drain to Source resistance of this electronic component is 50Ohm.
DG444DJ Features
4 Channels
Switch Circuit: SPST - NC
30mA Supply Current
Drain-to-Source resistance: 50Ohm
DG444DJ Applications
There are a lot of Vishay Siliconix DG444DJ Analog Switches & Multiplexers ICs applications.
- Battery-powered systems
- Audio and video signal routing
- SONET/SDH ADM
- Fiber In The Loop (FITL)
- T1/E1 Terminals
- MP3 players
- Intelligent PBX
- Relay Replacement
- ATM
- PDAs
