Parameters |
Factory Lead Time |
1 Week |
Mount |
Through Hole |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Number of Pins |
16 |
Weight |
1.627801g |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2007 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
160Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
450mW |
Technology |
CMOS |
Number of Functions |
4 |
Supply Voltage |
15V |
Base Part Number |
DG444 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Power Supplies |
512/+-15V |
Number of Channels |
1 |
Max Supply Voltage |
36V |
Min Supply Voltage |
13V |
Operating Supply Current |
5μA |
Nominal Supply Current |
1μA |
Power Dissipation |
450mW |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
250 ns |
Number of Inputs |
4 |
Voltage - Supply, Single/Dual (±) |
5V~36V ±5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
140 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
85Ohm |
Min Dual Supply Voltage |
7V |
Dual Supply Voltage |
20V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
60 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
4pF 4pF |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
250ns, 140ns |
Charge Injection |
-1pC |
Crosstalk |
-100dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
85Ohm |
Normal Position |
NC |
Height |
3.81mm |
Length |
21.33mm |
Width |
7.11mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
DG444DJ-E3 Overview
Shipping overseas is convenient with the electronic component packed in 16-DIP (0.300, 7.62mm). The advanced packaging method Tube provides high reliability. The multiplexer is located in Through Hole. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -40°C~85°C TA extended. In total, 16 terminations have occurred. High-quality output is provided by the electronic component's 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. The analog switch ics are built using SPST - NC switching circuits. If you are looking for variants of the digital switch, trying search with DG444. As far as internal resistance is concerned, it has 160Ohm. For functions related to 16 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. In a normalsituation, users should not supply the switches with voltage higher than 36V. Dual, Single supply type digital switch with a low cost. A low voltage of 13V should be applied to the electronic component. In order to operate this switch device, it would need a current of 5μA. Putting voltage greater than 1μA on the multiplexer may cause damage. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 22V. You should attach at least 7V voltage if you are using dual power supply. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. The 4 inputs need to be operated in order to work. This electronic component presents a Drain to Source resistance of 85Ohm.
DG444DJ-E3 Features
1 Channels
Switch Circuit: SPST - NC
5μA Supply Current
Drain-to-Source resistance: 85Ohm
DG444DJ-E3 Applications
There are a lot of Vishay Siliconix DG444DJ-E3 Analog Switches & Multiplexers ICs applications.
- PCMCIA cards
- Isolation
- Channel Banks
- Audio and video switching
- Digital access cross connects
- DSUs
- Remote Powered Equipment
- Cable Modem
- DVD-R
- Audio signal routing