DG444DVZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 16 |
| Published | 1999 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 16 |
| Resistance | 160Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | IT CAN ALSO OPERATE WITH 12V SINGLE SUPPLY |
| HTS Code | 8542.39.00.01 |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Operating Supply Voltage | 28V |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 100pA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 450 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 20V |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 18V |
| Off-state Isolation-Nom | 60 dB |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Switch-off Time-Max | 140ns |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
DG444DVZ Overview
The electronic part can be shipped overseas conveniently because it is packaged in TSSOP. In total, there have been 16 terminations. By its 1 channels, the electronic component provides high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. In this multiplexer, the internal resistance is 160Ohm. You can find the functions of the 16 pins in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. A voltage higher than 40V should not normally be supplied to the switches. Analogue multiplexers of the Dual, Single supply type that are cost-effective. A low voltage of 5V should be applied to the electronic component. This multiplexer would work with 100pA current. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. For this switch, a dual supply voltage is feasible, but it must not exceed 20VWhen using dual power supplies, you should attach at least 5V. A voltage of 28V can be used to operate the electronic component. Additional features include: IT CAN ALSO OPERATE WITH 12V SINGLE SUPPLY. Temperatures above 85°C should not be used to operate the switches.
DG444DVZ Features
1 Channels
100pA Supply Current
Additional Features: IT CAN ALSO OPERATE WITH 12V SINGLE SUPPLY
DG444DVZ Applications
There are a lot of Intersil (Renesas Electronics America) DG444DVZ Analog Switches & Multiplexers ICs applications.
- Medical systems
- T1/E1 Terminals
- Fiber to the Home
- Fault Tolerant Systems
- Residential Gateways, Home Gateway/Router
- Battery-powered systems
- Transmit
- RGB switches
- High-Voltage
- Mechanical reed relay replacement
